Bosch DS7400XiV4-EXP Spécifications télécharger pdf (Page 28)

DS7400XiV4-EXP | Reference Guide | 5.0 Programming the Control Panel EN | 28

Bosch Security Systems | 1/05| 4998154963B

5.0 Programming the Control

Panel

5.1 Entering Programmer’s Mode

To enter the Programmer's Mode, enter the

Programmer’s Code followed by [#][0]. Shorting the

program pads (see Section 3.0 Control Panel Installation

for location) on the control panel also enters

Programmer’s Mode.

The default Programmer’s Code is

[9][8][7][6]. If the system is reprogrammed

for 6-digit PINs, the default Programmer’s

Code is [9][8][7][6][5][4].

5.2 Reading Back a Program Address

To read back the value of a program address, enter that

program address followed by [#]. Each data digit is

displayed one data digit at a time. To view the second

data digit, press the [#] button again.

Figure 12 shows a sample display.

Figure 12: Program Address Display

1- Program address

2- Data Digit number

3- Value of the Data Digit

4- Control panel firmware revision

5.3 Entering a Value in a Program

Address

To enter a value in the program address:

1. Enter the program address.

2. Enter the value for each data digit and press [#] to

save the values.

The display shows the program address and displays

the value of each data digit after you enter it. The data

is programmed (saved) when you press the [#] key. The

control panel automatically increments to the next

program address.

• To program the next address, enter the desired

information.

• To read back the value of the address, press the [#]

key.

• To program a different address, press the [*] key

two times and enter the program address.

• If you make a mistake at any time, press the [*]

key twice before pressing the [#] key. This clears

the display and allows you to enter the desired

program address.

5.4 HEX Values

Some data digit values are greater than 9. These values

must be programmed by pressing the [*] key followed

by some other number. These values are displayed as

HEX characters (A to F) when entered. Example:

entering [*][0] at the keypad displays A.

The HEX character values are shown in Table 12.

Table 12: HEX Character Values

Keys Pressed HEX Character

[*][0] A

[*][1] B

[*][2] C

[*][3] D

[*][4] E

[*][5] F

5.5 Defaults

The DS7400XiV4 is shipped as a working, pre-

programmed control panel. Many of the programming

addresses might already be set to the values you need.

5.5.1 Defaulting the Control Panel

Entering [0][1][#] in Program Address 4058

immediately resets the control panel to the

factory default. Any programming already

done by the installer is erased. This action

cannot be reversed. Only enter [0][1][#] in

Program Address 4058 when you are

completely sure you want to erase all

installer programming.

To set the control panel’s programming values back to

the default:

1. Enter the programming mode.

2. Enter [4][0][5][8][0][1][#].

5.6 Exiting Programmer’s Mode

To exit Programmer’s Mode, press the [*] key for at

least 2 seconds. If no keypad entries are made for 4

minutes, the control panel automatically exits

Programmer’s Mode.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Bosch DS7400XiV4-EXP Spécifications Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7400XiV4-EXP