Bosch DS7400XiV4-EXP Spécifications télécharger pdf (Page 117)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 117

Bosch Security Systems | 1/05| 4998154963B

• All other keypads should be connected to the

keypad bus and may be placed as needed (within

the noted wiring limitations in the installation

manual).

• One keypad must be assigned as address 1.

7.2.12 Open/Close Report Control Programming

Open and Close Reports: If programmed, these

reports are sent when the system is armed or disarmed.

They may be sent independently for the opening and

closing of each area, or the first area to open and the

last area to close may send the reports.

• Send Trouble at Close for Bypassed Zones: If

programmed, a trouble report will be sent for each zone

bypassed when the system is armed.

• Alternate between both Phone Numbers: If

programmed, open and close reports will be sent to

phone number one first. If phone number one does not

pick-up, the control panel will alternate to phone

number two. If phone number two does not pick-up,

the control panel will alternate back to phone number

one. It will alternate between both phone numbers until

successful.

7.2.13 Report Programming

Reports: For pulse formats, reports are programmed by

entering data in the reporting and extended digits. The

report will send the data programmed for each event.

For SIA and Contact ID, the report formats are fixed

and may be activated by placing a 1 in the reporting

digit.

• To disable a report, enter a 0 in the reporting digit.

• To send the Man No. along with Open and Close

reports, program an “F” (enter [*][5] at the keypad)

in the extended digit.

Keypad Fire Alarm: This report is sent when a fire

alarm has been activated by the “A” emergency key.

Keypad Fire Restoral: This report is sent when a

keypad fire alarm has been restored using the [System

Reset] command.

Keypad Emergency Alarm: This report is sent when

an emergency alarm has been activated using the “B”

emergency key.

Keypad Panic: This report is sent when an emergency

alarm has been activated using the “C” emergency key.

Keypad Tamper: For keypads fitted with a wall

tamper switch, this report is sent when the keypad is

removed from the wall.

Keypad Tamper Restoral: For keypads fitted with a

wall tamper switch, this report is sent when the keypad

is properly replaced on the wall after experiencing a

tamper condition.

Zone Function Alarm: An alarm report is sent when

a zone alarm occurs. Alarm reports are enabled by

zone function. Program this report for any zone

functions you wish to send an alarm report about. For

local zones (no reports), do not program an alarm

report. The zone number will automatically be sent for

this report in SIA or Contact ID format.

Zone Function Restoral: This report is sent when the

zone alarm and trouble conditions are cleared. The

zone number will automatically be sent for this report

in SIA or Contact ID format.

Zone Function Trouble: This report is sent when a

zone trouble condition occurs. This can be an open

circuit, if the zone is programmed for “trouble on

open”, a multiplex tamper switch being activated, or a

multiplex zone not communicating with the control

panel. The zone number will automatically be sent for

this report in SIA or Contact ID format.

Zone Function Bypass: This report is sent when a

zone is bypassed. (Note: Fire zones can never be

bypassed.) Zone bypass reports for non-24 hour zones

are sent with the closing report. Bypass reports for 24

hour zones are sent when the zone is bypassed. If a

zone is force armed, the bypass report is sent with the

partial close report. If a 24 hour or non-24 hour zone

is custom armed, the bypass report is sent with the

partial close report.

Zone Function Bypass Restoral: This report is sent

when the zone bypass is cleared. For non-24-hour

zones the bypass restoral is sent with the open report.

Bypass restoral reports for 24 hour zones are sent

when the zone is manually restored. The bypass

restoral report for a zone that was force armed is sent

when the zone is restored. If a 24 hour or non-24 hour

zone was custom armed, the bypass restoral is sent

with the open report.

Open: This report is sent when the system has been

disarmed. In SIA or Contact ID formats, the user

number for the person who disarmed the system will

be sent with this report. To send the user number

along with an Open report in other formats, program

the extended digit of the report as *5. In Contact ID

format, the area number will also be sent along with

this report. The Open report will only be sent if a

Close report was sent previously.

1 2 ... 112 113 114 115 116 117 118 119 120 121 122 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Bosch DS7400XiV4-EXP Spécifications Page 117

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7400XiV4-EXP