Bosch DS7400XiV4-EXP Spécifications télécharger pdf (Page 114)

DS7400XiV4-EXP | Reference Guide | 7. Reference Materials EN | 114

Bosch Security Systems | 1/05| 4998154963B

Ground Start: This is an output programmed to

activate for 3 seconds when the phone line is seized. It

is intended for use with ground start phone systems that

require a momentary short to ground to obtain a dial

tone.

• Connect a separate 12 VDC, DPDT relay.

• Connect both relay contact commons to ground,

and connect the Normally Open of each contact to

terminal positions 13 and 16 (one to terminal 13,

the other to 16) of the DS7400Xi.

• This output follows all areas regardless of how data

digit 2 of the output programming address is

programmed.

• Not intended for UL Listed systems. Not for use

with phone line monitors.

System Status (ready to arm): This is an output

programmed to follow the Status LED of the keypad.

• It will activate when the system is ready to arm

with no zones violated.

Zone Alarm: This is an output programmed to activate

when a zone is in an alarm condition.

• It will remain activated until the system is disarmed

or the bell cut-off time expires.

• This output is intended to activate alarm bells and

sirens.

• This will not activate from Silent or Invisible Zones.

Zone Alarm Delayed by 20 sec.: This is an output

programmed to wait 20 seconds after a zone enters an

alarm condition to activate.

• It will remain activated until the system is disarmed

or the bell cut-off time expires.

• This output is intended to activate alarm bells and

sirens, but provides a delay to allow the user to

silence the system before it activates.

Output Functions: Output Functions can be

programmed to follow system events or to follow one or

two specific zones in a “cross-matrix” fashion (see

Input/Output Cross-Matrixing).

• These Output Functions can be programmed to

control Octal Relay outputs or Multiplex Bus

outputs.

• Output Functions are programmed in addresses

2772 to 2843.

Input/Output Cross Matrixing: Input/Output Cross

Matrixing allows Output Functions to follow the status

of specific input zones (zones 1 through 248 only).

• Outputs can be programmed to follow any

combination of one or two zones, open or closed,

with the system armed or disarmed.

• If programmed to latch, the output will latch until

a valid PIN is entered at the keypad.

Keypad Sounder Output: This is an output

programmed to follow the keypad sounder.

• It activates during the entry pre-alert and during

any day monitor alarm. It does not follow

momentary keypad beeps such as keystrokes,

chimes, and so on.

Access Output: This is an output programmed to

activate for 10 seconds when an access control PIN is

entered at the keypad.

Panic/Duress Output: All outputs, including the three

on-board outputs, the Octal Relays, and the Output

Functions, support a Panic/Duress function. This

output will follow Duress activations, Keypad

Emergency Keys B and C, and Invisible and Silent

Zone alarms. It will only be reset by a user

acknowledgement and will not reset after the burglary

bell time-out occurs. Duress activations will latch until

acknowledged by a user.

Multiplex Bus Outputs: The DS7400Xi supports up

to 60 DS7465i Input/Output Modules.

• These modules are connected to the multiplex bus

and provide one input loop and one Form "C"

output relay.

• The input loop operates the same as all other

multiplex inputs.

• The output loop can be programmed to follow

Output Functions.

• Multiplex Bus outputs can be bypassed using the

bypass function. If an output zone is bypassed

while it is ON, it will turn OFF. The bypass will

not be removed when the system is armed and

then disarmed; it must be cancelled by entering

the bypass command again or by canceling all

bypasses.

DS7465i Module outputs will not pulse,

even if programmed to do so.

1 2 ... 109 110 111 112 113 114 115 116 117 118 119 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Bosch DS7400XiV4-EXP Spécifications Page 114

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7400XiV4-EXP