Bosch DS7400XiV4-EXP Spécifications télécharger pdf (Page 26)

DS7400XiV4-EXP | Reference Guide | 4.0 Operating Guide EN | 26

Bosch Security Systems | 1/05| 4998154963B

4.7 Testing Your System

4.7.1 Zone (System Walk) Test

The Zone Test is used to confirm that detectors report

alarms to the keypad. A Zone Test works on all zones,

except 24-hour zones and fire zones. While the keypad

is in a Zone Test, no control panel alarms activate an

alarm, except 24-hour zone alarms and fire alarms;

these override the Zone Test function.

To perform a Zone Test:

1. Press [PIN][#][8][1].

• The DS7445i/DS7445V2 zone LEDs of

any untested zones will flash.

• The DS7447E/DS7447V2 displays “Test

Zone” followed by the zone number of any

zones that have not been tested.

2. Pick any untested zone and manually cause a

detector to alarm using a method specified in the

detector’s installation instructions.

• The DS7445i/DS7445V2 zone LED for the

zone currently being tested will turn on

steady.

• The DS7447E/DS7447V2 displays “Now

Testing” followed by the zone number of

the zone that is currently being tested.

3. Clear the alarm condition from the detector using a

method specified in the detector’s installation

instructions, and trigger an alarm on the next

detector in that zone. Continue until all detector's

in that zone are tested.

• As each zone is tested, its

DS7445i/DS7445V2 zone LED turns off.

• As each zone is tested, the

DS7447E/DS7447V2 display returns to

“Test Zone” and indicates the remaining

untested zones.

4. Test each zone.

5. Exit the Zone Test using [PIN][#].

4.7.2 Battery Tests

You can test the battery and the local sounder, or just

test the battery. If these tests are performed from a

Master keypad, it must be in Single Partition Mode.

System Tests are not available from RF (wireless)

keypads.

To start a Local Battery/Sounder Test:

Press [PIN][#][8][5].

All keypad LEDs turn on. The keypad sounder and all

alarm sounding devices operate for two seconds. If the

test fails, the control panel indicates a control problem.

See Section 4.6 Keypad Error Displays.

To start a Battery Test:

• Press [PIN][System Reset]. The control panel

performs a battery test. The control panel reports a

Low Battery or a Low Battery Restoral if

necessary.

4.7.3 Communication Test

This test is available only if the system transmits

alarms and system information to a monitoring service,

and is programmed by the security installing company

to permit control panel tests. This test can be

performed from a Master Keypad. The account code

for area #1 is sent with the test report. System Tests

are not available from RF (wireless) keypads.

To initiate a Communication Test:

Press [PIN][#][8][2].

A long beep sounds. A test report is sent to the

monitoring service. If the test fails, the keypad sounds

continuously. Press [System Reset] to silence the

sounder.

This test might take several minutes to

complete.

4.7.4 Fire Walk Test

This test is used to confirm that smoke detectors report

alarms to the keypads. The Fire Walk Test tests all fire

zones, including verified fire and waterflow.

At the start of the Fire Walk Test, a Fire Walk Test

report, if programmed, is sent to the central station.

Fire alarm reports are not sent to the central station

during the Fire Walk Test. A Fire Walk Test restoral is

sent upon completion of the Fire Walk Test.

The Fire Walk Test runs for 20 minutes after it is

started. The test time is extended to 20 minutes every

time another zone is tested.

When a fire zone is tested, any output programmed to

follow that zone activates for 5 seconds.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Bosch DS7400XiV4-EXP Spécifications Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7400XiV4-EXP