Bosch DS7400XiV4-EXP Spécifications télécharger pdf (Page 25)

DS7400XiV4-EXP | Reference Guide | 4.0 Operating Guide EN | 25

Bosch Security Systems | 1/05| 4998154963B

4.6.2 System Faults

System faults can be read from any keypad

because they are system-wide. All other Error

Displays are limited to the area the standard

keypad is in. If you are on a Master keypad,

you can read Error Displays one area at a

time.

System faults are designated as shown in Table 11.

Table 11: System Faults

[#][8][7] Displays: [#][8][9] Displays:

RAM Fault System Fault 01

ROM Fault System Fault 02

EEPROM Fault System Fault 03

Ground Fault System Fault 04

2Ph/Bell Fault = loss of

communication to DS7420i

System Fault 10

Line 1 Fault = DS7420i

phone line 1 fault

System Fault 11

Line 2 Fault = DS7420i

phone line 2 fault

System Fault 12

Bell Fault = DS7420i bell

circuit fault

System Fault 13

Aux. Relay Fault = DS7420i

auxiliary relay fault

System Fault 14

Oct. Relay Fault = loss of

communication to DX3010

System Fault 20

Serial IF Fault System Fault 30

Printer Error System Fault 33

Reserved for older panels System Fault 50

AR IB Queue Full = modem

buffer full

System Fault 51

AR Host Down = network

data switch down

System Fault 52

AR Unreg. Modem =

modem not registered

System Fault 53

AR Power Fail = power

source below defined

threshold

System Fault 54

AR Network Lost = loss of

network

System Fault 55

AR Modem HW Err =

modem hardware error

System Fault 56

AR Modem SW Err =

modem software error

System Fault 57

AR Opt. Bus Err = loss of

communications to ARDIS

module

System Fault 58

AR Corrupt MSG =

message error

System Fault 59

Table 11: System Faults (continued)

[#][8][7] Displays: [#][8][9] Displays:

AltComm A Tx Err

SerialBI/F Fault

SerialB Tx Error

SerialB Rx Error

SerialBFlowError

AltComm A Error

AltComm B Error

AltComm B Tx Err

System Fault 60

4.6.3 Event History

The History Buffer stores the last 400 events in

memory. The DS7447E/DS7447V2 can display all of

these events. If this test is performed from a Master

keypad, it must be in Single Partition Mode. The

DS7445i/ DS7445V2 can only display those zones (1

to 16) that have alarmed since the last Event History

Readback. The RF3341 cannot display history events.

To readback the Event History Buffer:

• Press [PIN][#][8][9]. On a DS7447E/DS7447V2

keypad, the last event to take place will be

displayed. On a DS7445i/DS7445V2 keypad, the

zone LEDs for any zones that have alarmed since

the last Event History Readback in that area will

flash.

• Scroll through the events using the [9], [6], and [#]

keys as follows:

• To begin scrolling back through the

events, press the [#] key. The [#] key

scrolls you back through the history line

by line.

• The [9] key scrolls you back in reverse

chronological order by event.

• A [6] scrolls you back up through the

events (toward the most recent) by event.

Each event consists of two or three lines or display

screens. The first line/screen is the event title and user.

The second line/screen is the date of the event or the

change being made. If there is a third line/screen, it is

the date of the change.

When performing this from a Master

keypad, each area (partition) displays its

own history as the user scrolls through the

areas.

• To exit the Event History Mode, press the [*] key

or wait 20 seconds and the keypad exits

automatically.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Bosch DS7400XiV4-EXP Spécifications Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7400XiV4-EXP