Bosch B450 Guide d'installation Page 76
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1. Enter your Master Code and press [6][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the day, month, year, hour, and minute in DD, MM, YY, HH, MM format (where DD is
the day of the month, MM is the month of the year, YY is the year, HH is the hour of the day,
and MM is the minute of the day) and press [AWAY]. Use 24:00 hour format when
programming the hour of the day. Two beeps sound and the STAY and AWAY indicators are
extinguished. If a long beep sounds, an error occurred when you entered the date and time.
Example
To set the date and time for 1st January 2009 at 10:30 PM, enter:
[2 5 8 0 6][AWAY][0 1 0 1 0 9 2 2 3 0][AWAY]
Walk Test Mode
Walk Test Mode allows you to test detection devices to ensure they are functioning correctly.
Before activating Walk Test Mode, isolate any zones that are not required for testing. Refer to
Isolating zones, page 56 for more information.
To enter Walk Test Mode:
1. Enter the passcode and press [7][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash. The codepad beeps once per sec when Walk Test Mode is active.
2. Unseal and seal the zones to be tested. The codepad sounds one long beep and the horn
speaker sounds one short beep each time a zone is sealed or unsealed.
3. Press [AWAY] to exit from this function. Two beeps sound and the STAY and AWAY
indicators are extinguished. The system returns to the disarmed state.
Event Non-Volatile Memory Recall Mode
This function allows you to play back the last 40 system events that occurred. Event Non-
volatile Memory Recall Mode reports all alarms and each arming or disarming of the system
and helps with troubleshooting system faults. The events are shown using the codepad
indicators. The event memory is not lost even with the power supply off.
To enter Event Memory Recall Mode:
Enter your Master Code and press [8][AWAY]. Three beeps sound. The events are played back
by the codepad indicators in reverse chronological order.
Example
If the events occurred in the following order:
Sequence Event
1 System armed in AWAY Mode
2 Alarm in Zone 3
3 Alarm in Zone 4
4 System disarmed
5 System armed in STAY Mode
The alarm memory plays back in this order:
7.2.10
7.2.11
76 en | System Functions Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels