Bosch B450 Guide d'installation Page 75
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Turning Outputs On and Off
If an output is programmed for remote operation, you can turn the remote output on or off
using this Master Code function or remotely using the A-Link Software or smartphone
application (RSC).
To use this Master Code function, you must program one or more of the outputs with these
Output Event Types:
Remote control output 1 = Output Event Type 2,8
Remote control output 2 = Output Event Type 2,9
Remote control output 3 = Output Event Type 2,10
Remote control output 4 = Output Event Type 6,2
Remote control output 5 = Output Event Type 6,3
Remote control outputs 6 = Output Event Types 6,4
Remote control outputs 7 = Output Event Types 6,5
Remote control outputs 8 = Output Event Types 6,6
Remote control outputs 9 = Output Event Types 6,7
Remote control outputs 10 = Output Event Types 6,8
Remote control outputs 11 = Output Event Types 6,9
Remote control output 12 = Output Event Type 6,10
To turn an output on from the remote codepad:
1. Enter your Master Code and press [5][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of the output (1 to 12) and press [AWAY]. Three beeps sound and the
output turns on.
3. Repeat Step2to turn on another output.
4. Press [AWAY] to exit from this function. Two beeps sound and the STAY and AWAY
indicators are extinguished.
Example
If Output 2 is programmed as 2,9,1,0,0,0 in Locations 442 to 447, the Master Code holder can
turn on this output by entering:
[2 5 8 0 5][AWAY][2][AWAY][AWAY]
To turn an output off from the remote codepad:
1. Enter your Master Code and press [5][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of the output (1 to 12) and press [STAY]. Two beeps sound and the
output turns off.
3. Repeat Step2to turn off another output.
4. Press [AWAY] button to exit from this function. Two beeps sound and the STAY and AWAY
indicators are extinguished.
Setting the Date and Time
Use this function when the date and time must be changed or if the system was powered
down.
If the date and time is not set, the date and time fault appears only when the Auto Arming
Time is programmed in Locations 482 to 485, or when you enter Fault Analysis Mode by
holding down [5].
To set the new date and time:
7.2.8
7.2.9
Control Panel System Functions | en 75
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels