Bosch B450 Guide d'installation Page 121
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
By default, the control panel waits approximately 30 sec for receipt of a valid handshake tone
after it dials the monitoring station. The handshake tone indicates to the control panel that it
reached the monitoring station and can now transmit its messages. Selecting this option
extends this wait time from 30 sec to 60 sec.
Item Location Default
Communicator Options 2 178 0
Value Description
1 Arm/Disarm reports only if previous alarm
2 Arm/Disarm reports for STAY Mode 1 and STAY Mode 2
4 Delay siren until transmission complete
8 Extend time to wait for handshake from 30 to 60 sec
Communicator Options 3
1 – Set DTMF Dialing Pulses to 1 Digit/Sec
If this option is not selected, the DTMF dialing format dials at 5 digits per sec (that is, 100 ms
tone, 100 ms pause, 100 ms tone, 100 ms pause).
If this option is selected, the DTMF dialing format dials at the rate of 1 digit per sec (that is,
500 ms tone, 500 ms pause).
2 – Lockout Telephone Line Fail Alarm
Selecting this option allows an audible alarm only once per arming cycle when the control
panel detects the telephone line is cut or disconnected. This option does not follow the
Swinger Shutdown Count for Siren, in which you can program the number of times a zone can
sound an alarm during an arming cycle. Use Location 176 to program the telephone line fault
options.
Item
Location Default
Communicator Options 3 179 2
Value Description
1 Set DTMF dialing pulses to 1 digit/sec
2 Lockout telephone line fail alarm
4 Reserved
8 Reserved
A-Link Options
The following A-Link options are available only for link through the telephone line. The options
are not related to connection through network.
1 – Enable Upload/Download Using A-Link
Select this option to use the A-Link Plus software to program the control panel remotely. The
control panel does not respond to A-Link if this option is not selected.
13.12
13.13
Control Panel Communicator Information | en 121
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels