Bosch B450 Guide d'installation Page 74
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3. Enter the desired call forward disable sequence.
For example, program [# 6 1 #] to disable the call forward – no answer sequence, or [# 2 1 #]
to disable the call forward – immediate sequence.
Telco Arm/Disarm Dialing Digits
Digit required Number to program Digit required Number to program
0 0 7 7
1 1 8 8
2 2 9 9
3 3 15 [STAY]5
4 4 * [STAY]1
5 5 # [STAY]2
6 6 4 sec pause [STAY]3
4. Press [AWAY]. Two beeps sound and the system returns to the disarmed state. You can
suspend the telco disarming sequence at any time. To disable the telco disarming sequence:
Enter your Installer Code and press [3][AWAY][2] [AWAY][STAY][5][AWAY].
Setting STAY Mode 2 Bypass Zones
This function allows the installer to select the zones that are automatically isolated when the
system is armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and hold [0] until two beeps sound. Refer to Arming
the system from STAY Mode 2, page 54 for more information.
To set STAY Mode 2 zones:
1. Enter the passcode and press [4][AWAY]. Three beeps sound and the STAY indicator
flashes.
2. Enter the number of the zone you want to automatically isolate and press [STAY]. The
corresponding zone indicator flashes.
3. Repeat step 2 for each zone you want to select.
Notice!
As each zone is selected to be isolated, the corresponding zone indicator flashes. If you make
a mistake, enter the incorrect zone number and press [STAY]. This zone is no longer selected
to be isolated and the zone indicator is extinguished.
4. Press [AWAY]. Two beeps sound and the system returns to the disarmed state. The
indicators for the zones you selected and the STAY indicator are extinguished.
Example
If you want to select zones 2, 5, and 6, enter:
[1 2 3 4 4][AWAY][2][STAY][5][STAY][6][STAY] [AWAY]
You can disable selected zones to be automatically isolated for STAY Mode 2 at any time.
To disable STAY Mode 2 zones:
Enter your passcode and press [4][AWAY] [AWAY].
7.2.7
74 en | System Functions Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels