Bosch B450 Guide d'installation Page 36
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1. Power off the control panel.
2. Set the B426 rotary address switch to 9.
3. Remove the jumper for Tamper and install the jumper for Mode.
4. Change the computer network address to 169.254.1.2.
5. Connect the B426 to the computer with a network cable.
6. Power on the control panel.
Configure for the web
1. From Internet Explorer on the computer, go to http://169.254.1.1. The B426 Login
interface opens. Enter password “B42V2” to access the B426 configuration web interface.
2. Click Factory Default, then click OK to confirm.
3. Click Encryption and Security Settings.
4. Change Web and Automation Security to Enable, then click OK to confirm.
5. Click Maintenance.
6. Change Web Access Enable to Yes,
7. Change Panel Programming Enable to Enable, then click OK to confirm.
8. Click Save and Execute, then click OK to save the changes.
9. Click Logout to log out of the web configuration interface.
10. Power off the control panel.
Restore connection
1. Change the computer network address to its previous value.
2. Remove the cable from the B426 to the computer, and restore the connection in the
diagram.
3. Remove the Mode jumper, and install the Tamper jumper.
4. Turn the rotary address switch to “1”.
Reset the B450/B442 modules to factory default
If the parameters of the B450/B442 are already set to their factory default values, skip the
steps below and go to the next set of steps in Configure A-Link Plus.
1. Power off the control panel.
2. Set the rotary address switch of the B450 to “0”; remove the Tamper jumper.
3. Connect the B450 to the computer with a male to male USB cable.
4. Power on the control panel.
5. Wait until the heartbeat LED on the B450 flashes 3 times per second and the status LED
on the B442 flashes 1 time per second. The flashing indicates the startup process has
completed.
6. Open the “Tera Term” software on the computer and select the serial port named B450
Config Interface.
7. Enter the B450 USB menu interface. Press [ENTER].
8. Enter passcode “B450”. The main menu opens.
9. Enter “5” to select Reset To Factory Default. At the message “Are you sure (Y to default, N
to exit)”, input “Y” to confirm. The interface returns to the main menu.
10. Enter “8” to confirm Save and Exit. Turn off the Tera term.
11. Power off the control panel.
12. Install the Tamper jumper and turn the rotary address switch to 2.
13. Power on the control panel.
Configure A-Link Plus
36
en | Accessories Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels