Bosch B450 Guide d'installation Page 109
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Select this option to force the control panel to send a Test Report after the siren is reset. This
can be used to indicate to the monitoring station that the control panel itself was not
tampered with during the alarm period.
4 – Auto Arm in STAY Mode 1
Select this option if automatic arming in STAY Mode1 is preferred to automatic arming in
AWAY Mode.
Program the time that the control panel automatically arms itself in Locations 482 to 485. Set
the Auto Arming Pre-Alert Time in Location 481
For partitioned control panels, both areas are automatically armed.
8 – STAY Indicator To Display Day Alarm Status
If this option is selected, the STAY indicator flashes once every 3 sec when Day Alarm is
enabled.
Specify Day Alarm zones in Location 265.
You can turn Day Alarm on and off by holding down [4] for 2 sec. Three beeps indicate Day
Alarm is turned on and two beeps indicate Day Alarm is turned off.
Consumer Options 2
Item Location Option Default New
Consumer Options 2 0497 1 = Codepad displays extinguish after 60 sec.
2 = Single button arming allowed (AWAY/STAY
Modes 1 and 2)
4 = Single button disarming allowed (STAY
Modes 1 and 2)
8 = Alarm memory reset on disarm
2
1 – Codepad Display Extinguish after 60 Sec
If this option is selected, all indicators on the remote codepad display are extinguished if a
button is not pressed for 60 sec. The indicators lights again when there is an alarm (except a
silent alarm), when a button is pressed on the codepad, when the AC MAINS fail beeps, or if
the Entry Timer is activated.
2 – Single Button Arming Allowed
If this option is selected, the hold-down functions for arming in AWAY Mode, STAY Mode 1 and
STAY Mode 2 are functional.
4 – Single Button Disarming Allowed
This option operates only when Option 2 in this location is also selected. This option allows
hold-down functions for disarming from STAY Mode 1 and STAY Mode 2.
8 – Alarm Memory Reset on Disarm
If this option is selected, the alarm events memory clears from the remote codepad when the
system is disarmed. If this option is not selected, the system must be armed and disarmed
again to clear alarm memory from the remote codepad.
11.6
Control Panel System and Consumer Options | en 109
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels