Bosch B450 Guide d'installation Page 138
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Example
If Area 1 is armed in AWAY Mode or STAY Mode1 or STAY Mode 2, Output Event Type 5,6
operates. The output is reset when Area 1 is disarmed.
5,10 Area 1 Is Disarmed
5,11 Area 2 Is Disarmed
These two outputs operate when their corresponding area is disarmed. The output is reset
when the corresponding area is armed.
Example
If Area 1 is disarmed, Output Event Type 5,10 operates. The output is reset when Area 1 is
disarmed.
5,14 Any Areas Armed
This output operates when either Area 1 or Area 2 is armed in AWAY Mode or STAY Mode 1.
The output is reset when both areas are disarmed.
5,15 Any Areas Disarmed
This output operates when either Area 1 or Area 2 is disarmed. The output is reset when both
areas are armed in AWAY Mode or STAY Mode 1 or STAY Mode 2.
6,2 Remote Control 4
6,3 Remote Control 5
6,4 Remote Control 6
6,5 Remote Control 7
6,6 Remote Control 8
6,7 Remote Control 9
6,8 Remote Control 10
6,9 Remote Control 11
6,10 Remote Control 12
These outputs operate output when using the master code function or A-Link software or
Smartphone App (RSC) to turn remote output on. The output is reset when using the master
code function or A-Link software or Smartphone App (RSC) to manually turn remote output off
or automatically turn remote output 3 off when the ON time expires if output polarity is from 3
to 6 or from 10 to 13.
Output Polarity
There are fifteen different polarities. Each polarity is designated by a number that you program
into the appropriate location for the output.
0 – Output Not Used
If an output is not required, program the polarity as 0.
1 – Normally Open, Going Low
This polarity is normally open circuit and switches to 0 V when the event occurs. The output
switches back to open circuit when the event is restored. Time parameters do not apply to
this polarity.
2 – Normally Open, Pulsing Low
This polarity is normally open circuit and switches to pulsing 0 V when the event occurs. The
output switches back to open circuit when the event is restored. Time parameters vary the On
time (Time base) and Off time (Time Base*Time Base Multiplier) of the pulse.
3 – Normally Open, One-Shot Low
This one-shot polarity is normally open circuit and switches to 0 V when the event occurs. The
output switches back to open circuit when the time parameter setting expires. This one-shot
time setting always runs its full duration and cannot be manually reset.
4 – Normally Open, One-Shot Low with Reactivate
15.3
138 en | Programmable Outputs Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels