Bosch B450 Guide d'installation Page 107
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1 – Codepad Panic to Be Silent
If this option is selected, a Codepad Panic Alarm or Radio Remote Panic Alarm does not
operate the horn speaker, the bell, or the strobe outputs. If this option is not selected, all
three outputs operate after a Codepad Panic Alarm is activated when a user presses [1] and
[3] or [STAY] and [AWAY] at the same time on the remote codepad. Selecting this option does
not affect the operation of the communication report.
2 – Codepad Fire to Be Silent
If this option is selected, a Codepad Fire Alarm does not operate the horn speaker, the bell, or
the strobe outputs. If this option is not selected, all three outputs operate after a Codepad
Fire Alarm is activated when a user presses [4] and [6] at the same time on the remote
codepad. Selecting this option does not affect the operation of the communication report.
4 – Codepad Medical to Be Silent
If this option is selected, a Codepad Medical Alarm does not operate the horn speaker, the
bell, or the strobe outputs. If this option is not selected, all three outputs operate after a
Codepad Medical Alarm is activated when a user presses [7] and [9] at the same time on the
remote codepad. Selecting this option does not affect the operation of the communication
report.
8 – Access Denied (Code Retries) to Be Silent
If this option is selected, a Codepad PIN Error Alarm does not operate the horn speaker, bell,
or the strobe outputs. If this option is not selected, all three outputs operate after a Codepad
PIN Error Alarm occurs. Selecting this option does not affect the operation of the
communication report.
System Options 3
Item Location Option Default New
System Options 3 0494 1 = AC fail after 1 hr. (Disabled = after 2 min.)
2 = Ignore AC fail
4 = Pulse count handover allowed
8 = Handover delay to be sequential
8
1 – AC Fail after 1 Hour
If this option is selected, the MAINS indicator flashes when the AC MAINS supply is
disconnected. An AC Loss signal (Contact ID Event Code 301) is transmitted to the base
station receiver after the AC MAINS supply is disconnected continuously for longer than 60
min.
If this option is not selected, the MAINS indicator flashes and an AC Loss signal (Contact ID
Event Code 301) is transmitted to the base station receiver after the AC MAINS power is
disconnected continuously for 2 min.
The MAINS indicator stops flashing when the AC MAINS supply is restored longer than 2 min.
An AC Loss Restore Report is transmitted to the base station receiver after the AC MAINS
supply is restored continuously for more than 2 min regardless of whether this option is
selected.
2 – Ignore AC Fail
If this option is selected, the MAINS indicator does not flash and the codepad does not beep
every minute when the AC MAINS is disconnected from the control panel. If you want a
programmable output to operate when the AC MAINS fails, use Output Event Type 1,4 AC Fail.
4 – Zone Pulse Count Handover
11.3
Control Panel System and Consumer Options | en 107
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels