Bosch B450 Guide d'installation Page 29
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Flash pattern Function
ON steady A trouble condition is prohibiting the module from
controlling the heartbeat LED.
OFF steady Module is not powered or some other trouble condition is
prohibiting the module from controlling the heartbeat LED.
WE800EV2
The WE800EV2 is designed to provide a convenient ON/OFF control for the Solution
2000/3000 series control panel. Provision is also made for the control of up to two (2)
external devices via on-board relays.
Install the module
1. Remove the small knockout in the Solution 2000/3000 control panel for the antenna and
insert the supplied rubber grommet.
2. Install the WE800EV2 PCB in the control panel with the top of the PCB in the slot
provided at the top of the case and secure with the provided screw at the bottom of the
PCB.
3. Thread the antenna wire through the grommet into the “ANT” terminal.
Wire to the control panel
Connect the 3 pin plug to the jumper labeled WE800 on the control panel. Note that the
connector will only install one way. If the relays are to be used, a wire will need to be
connected from the +12V terminal on the WE800EV2 to a +12 terminal on the control panel.
Add/delete keyfobs
Notice!
When purchasing a WE800EV2 kit, the keyfobs supplied are already learned to the WE800EV2
with both relays set for momentary operation. If a different relay set-up is required, delete the
keyfobs, then add them back again.
To add keyfobs:
1. Press the Learn/Delete switch once. Note that the LED will flash rapidly.
2. Press the button on the keyfob to be learned that corresponds to the desired relay
function.
Button 1 – Both outputs momentary
Button 2 – Output 1 toggling. Output 2 momentary.
Button 3 – Output 2 toggling. Output 1 momentary.
Button 4 – Both outputs toggling
3. Repeat for additional key fobs.
4. Press the Learn/Delete button when finished adding key fobs to complete the process.
To delete keyfobs:
Press and hold the Learn/Delete switch. Note that the LED will light and then extinguish after
4 seconds. The EEPROM is now erased. Individual keyfob deletion is not possible.
4.5
Control Panel Accessories | en 29
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels