Bosch B450 Guide d'installation Page 73
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
If your telephone is not answered within 20 sec, this feature redirects the incoming call to
another number anywhere in Australia. You can still make outgoing calls.
Telco Disarming Sequence
This option allows you to automatically disable the call forward sequence when you disarm the
system.
Change Telco Arm/Disarm Sequence
This feature allows you to program the telco arm sequence and telco disarm sequence. This
feature is available only if your telecommunication provider has the call forward option
available.
Telco Arm Sequence
This allows you to program the Call Forward – Immediate On sequence or Call Forward – No
Answer sequence that automatically operates when you arm the system in the AWAY Mode.
To program the telco arming sequence:
1. Enter your passcode and press [3][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1][AWAY] to change the telco arming sequence. Three beeps sound. If a call forward
sequence is already programmed, the sequence is displayed one digit at a time using the
remote codepad indicators. Refer to the table Telco Arm/Disarm Digits below for the
indicators and their meanings.
If no call forward sequence is programmed, an additional two beeps sound after entering this
mode. These two beeps normally sound after the last digit of the call forward sequence is
displayed.
3. Enter the desired call forward sequence.
For example, program [* 6 1][phone number][#] for the call forward – no answer sequence, or
[* 2 1][phone number][#] for the call forward – immediate sequence.
Notice!
When you program a * in the telco arm sequence, enter [STAY][1]. When you program the # in
the telco arm sequence, enter [STAY][2].
4. Press [STAY][2][AWAY]. Two beeps sound and the system returns to the disarmed state.
Example
If you want to automatically divert all unanswered incoming calls to another telephone number
(for example, 9672 1777) when the system is armed in AWAY Mode, enter:
[1234 3][AWAY][1][AWAY][STAY]
[1 6 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the telco arming sequence at any time. To disable the telco arming
sequence:
Enter your passcode and press [3][AWAY][1] [AWAY][STAY][5][AWAY].
To program the telco disarming sequence:
1. Enter your passcode and press [3][AWAY]. Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [2][AWAY] to change the telco disarming sequence. Three beeps sound.
If a telco disarming sequence is already programmed, the sequence is displayed one digit at a
time using the remote codepad indicators. Refer to the Telco Arm/Disarm Dialing Digits table
below for the indicators and their meanings.
If no telco disarming sequence is programmed, an additional two beeps sound after entering
this mode. These two beeps normally sound after the last digit of the sequence is displayed.
7.2.6
Control Panel System Functions | en 73
Installation Guide 2014.07 | 00n | F01U298026
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels