Bosch B450 Guide d'installation Page 122
- Page / 152
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2 – Enable A-Link Call Back
If this option is selected and a callback telephone number is programmed, the remote
programming computer must be connected to the telephone line programmed in the callback
telephone number in Locations 159 to 174.
If this option is not selected, the installer can connect to a customer’s control panel from any
remote location for Upload/Download operations without the control panel calling back to the
remote computer. The customer can initiate a modem call from the codepad by holding down
[6].
4 – Terminate A-Link Connection on Alarm
If an alarm occurs when the control panel is communicating with a remote computer using the
A-Link Plus software over the telephone line, the A-Link session is terminated and the relevant
alarm message is transmitted to the base station receiver.
If an alarm occurs that does not have to be reported to the base station receiver, the session
is not terminated.
Item
Location Default
A-Link Options 180 3
Value Description
1 Enable upload/download using A-Link
2 Enable A-Link callback
4 Terminate A-Link connection on alarm
8 Reserved
Sending reports with the network modules
Program IP Destination with A-Link Plus Software or text codepad
1. In receiver configuration, select Transmission Format as CSVIP , and enter Subscriber ID
Number.
2. In network configuration, select Network Module as Use, do not configure (or "Use and
Configure" through only A-link plus).
3. Enter IP Destination (IP + Port for Receiver 1 or Receiver 2), for example,
192.168.226.17:12000.
4. Enter CSVIP User Name and Password:
– Both user name and password, enter as user name with comma and password with
comma, for example, USER 1, 2580,.
– Only user name, enter as user name with two commas, for example, USER 1,,.
– Only password, enter as comma, followed by password with comma, for example, ,
2580,.
– No user name and password, only enter two commas.
5. Save the changes and download programming data from A-Link Plus to the control panel.
For A-Link Plus, enter 32 case sensitive alphanumeric characters for CSVIP User Name and
Password directly through keyboard.
For text codepad, enter sensitive alphanumeric characters as below table.
13.14
122 en | Communicator Information Control Panel
2014.07 | 00n | F01U298026 Installation Guide
- Control Panel 1
- Table of contents 3
- Introduction 8
- System Overview 10
- ICP-SOL3-P 12
- Configuration and Parts 13
- Parts list 14
- Order separately 14
- Installation workflow 15
- Accessories 16
- + 17
- PWR A B COM 17
- PWR A B COM 17
- Icon Codepad Indicators 18
- Text Codepad Indicators 19
- Installer Menu 23
- RADION keyfobs 27
- Keyswitches 27
- B308 Octo-output Module 28
- WE800EV2 29
- Figure 4.1: 31
- Figure 4.2: 31
- Figure 4.3: 31
- Accessories 31
- B426 -1 B450-2 35
- SwitcherRouter 35
- Internet 35
- Accessories 37
- TF008 Plug Pack (TF008-B) 40
- Remote Security Control 40
- Configuration 42
- Disable Factory Defaults 46
- Configuring for email 47
- System Operations 52
- Standard isolating 57
- Code to isolate 57
- Fault analysis mode 58
- Fault descriptions 59
- System Functions 62
- Change Domestic Phone Numbers 64
- Walk Test Mode 68
- Event Memory Recall Mode 68
- Master Code Functions 69
- Deleting User/Radio Codes 71
- Turning Outputs On and Off 75
- Setting the Date and Time 75
- User Code Functions 77
- Hold-Down Functions 77
- Send Test Report 80
- Domestic Dialing 81
- Zone Information 83
- EOL Resistor Value 84
- Zone Programming 85
- Zone Defaults 86
- Zone Types 90
- Zone Information 91
- Zone Pulse Count 92
- Zone Pulse Count Time 92
- Zone Options 1 93
- Zone Options 2 94
- Zone Report Options 95
- Keyswitch Zone Options 95
- Z1 COM Z2 96
- System Status Programming 98
- Test Reporting Options 99
- System Event Timers 101
- Auto Arming Time 104
- Auto Disarming Time 104
- Kiss-Off Wait Time 105
- Speaker Beep Volume 105
- System and Consumer Options 106
- System Options 3 107
- System Options 4 108
- Consumer Options 1 108
- Consumer Options 2 109
- Consumer Options 3 110
- Partitioning 111
- Zone allocations 112
- User code area assignments 113
- Codepad assignment 113
- Communicator Information 114
- Telco Arming Sequence 116
- Telephone Line Fail Options 118
- Communicator Options 1 119
- Communicator Options 2 120
- Communicator Options 3 121
- A-Link Options 121
- Installer Code 124
- User Codes 124
- Control Panel Access 125
- User Code Priority 126
- Control Panel Access 127
- Programmable Outputs 128
- Output Event Types 132
- Programmable Outputs 133
- Programmable Outputs 135
- Output Polarity 138
- Programmable Outputs 139
- RF Information 141
- Low Battery Restore Report 145
- Fault String 146
- Event String 147
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch B450
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels