Bosch Solution 16i Spécifications télécharger pdf (Page 41)

Bosch Security Systems 09/07 BLCC500R FTR1.02

Solution 16 i

Quick Start Guide

System > System Options >

Area Options MENU 7-7-1

1 Area 1 = Common Area N

2 First To Open Last To Close N

3 Reset Siren All Users (All Areas) Y

4 Power Up In Same State As Powered Down Y

5 Fault Acknowledge All Areas Y

6 Delay Trouble Beeps Y

7 Power Up Disarmed N

8 Reserved N

This location is a Bit option field. Press Keys [1] – [8] to turn ON and

OFF the required options. The option is selected or ON when the

coresponding zone indicator is on. Press [OK] To Save when finished.

(*** System Wide Parameter ***)

System > Options >

Keypad Idle Screen

MENU 7-7-2

0 = No Idle Screen 0

1 = Date and Time

(*** System Wide Parameter ***)

2 = Time

3 = Time + Temp Alternating

Use Keys [

] and [] keys or enter 0 - 3 Then Press [OK] To Program

The Keypad Idle Screen - Single Option Only.

System > Options >

Keypad Hi/Lo Temp

MENU 7-7-3

0 0 ˚C 0 0 ˚C

(*** System Wide Parameter ***)

Hi TEMP Lo TEMP

Using The 0 - 9 Keys Enter The High / Low Keypad Monitor

Temperature. You Should Enter Two Digits For Each Option

eg. 9 degrees = 09. Use The [] key to move to the next field.

Press [OK] to save or [MENU] to exit without saving.

Max Temp = 50 Min Temp = 0

System > Installer Options >

Installer Options MENU 7-7-4

1 Report/Log Entry/Exit Intstaller Menu N

2 Report/Log Program Data Change Y

3 Arm Only Installer Pin N

4 Reserved N

5 Auto Exit Installer Menu In 2 Hours Y

6 Auto Exit Service mode In 2 Hours Y

7 Reserved N

8 Factory Defaulting Allowed Y

This location is a Bit option field. Press Keys [1] – [8] to turn ON and

OFF the required options. The option is selected or ON when the

coresponding zone indicator is on. Press [OK] To Save when finished.

(*** System Wide Parameter ***)

System >Options >

Language

MENU 7-7-5

0 = English 0

1 = Alternate Language

(Enter Digits 0 – 1 To Select the Primary (English) Lanuage or the

Alternative Language Then Press [OK] To Save. Early Version Panels

Only Support English Language.

System > System Testing >

Walk Test All Zones

MENU 7-9-0

Battery Test

MENU 7-9-1

TESTING THE SYS TEM

You will need to be in programming mode before accessing

the test functions listed below.

Walk Test

Use the walk test command MENU 3-9-0 to test and verify

that all zones work correctly.

External Audible Test

Use MENU 4-9-0 to test and verify that all horn speakers

operate. This test will sound the horn speaker for two

seconds.

Internal Audible Test

Use MENU 4-9-1 to test and verify that all 12 VDC sirens

operate. This test will sound the siren for two seconds.

Strobe Test

Use MENU 4-9-2 To test and verify that the strobe operates.

This test will turn on the strobe until you manually stop the

test.

Battery Test

Use MENU 7-9-1 to test the back-up battery that is

connected to the control panel.

Communication Test

Use MENU 5-9-0 to test the telephone reporting capability

of the control panel. You can also activate a communication

test by holding down the Test / Mail key on the keypad.

1 2 ... 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Bosch Solution 16i Spécifications Page 41

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch Solution 16i