Bosch Solution 16i Spécifications télécharger pdf (Page 14)

Solution 16 i

Bosch Security Systems 09/07 BLCC500R FTR1.02

Quick Start Guide

Term ina l D esc rip tio ns

Nº Name Description

1 Earth

Earth wire from this terminal is connected

to the Mains earth.

~ (AC)

Connection of the 16-18V A.C. 50-60 Hz

adapter or internal transformer.

BAT (-)

BAT (+)

Negative and positive connections to the

stand-by battery. 12 VDC / 7.2AH

+12 V

GND

These terminals are used to power

detectors and other accessory devices.

(750mA Fused)

LAN +

LAN -

These terminals are used to power LAN

modules and devices. (750 mA Fused)

12 LAN A

Connect the LAN A data terminal of any

LAN device (eg. Keypads, expansion

boards) to this terminal. The control

panel supports up to 300 m of 24/0.20

(18 AWG) wire on these terminals.

13 LAN B

Connect the LAN B data terminal of any

LAN device (eg. Keypads, expansion

boards) to this terminal. The control

panel supports up to 300 m of 24/0.20

(18 AWG) wire on these terminals.

14 COMM+

Common positive terminal for system

outputs. This terminal is 2.5A PTC Fuse

protected.

OUT 1

OUT 2

OUT 3

OUT 4

Fully supervised programmable, open

collector outputs capable of driving

(sink) loads up to 1 amp for sirens, strobes

etc.

19 INPUT

Programmable Input for RF Receivers,

Keyswitch and other devices.

20 ZN 1 Zone 1 and 9 sensor loop input (+).

21 GND Common (-) for Zone 1 & 2 sensor loop.

22 ZN 2 Zone 2 and 10 sensor loop input (+).

23 ZN 3 Zone 3 and 11 sensor loop input (+).

24 GND Common (-) for Zone 3 & 4 sensor loop.

25 ZN 4 Zone 4 and 12 sensor loop input (+).

26 ZN 5 Zone 5 and 13 sensor loop input (+).

27 GND Common (-) for Zone 5 & 6 sensor loop.

28 ZN 6 Zone 6 and 14 sensor loop input (+).

29 ZN 7 Zone 7 and 15 sensor loop input (+).

30 GND Common (-) for Zone 7 & 8 sensor loop.

31 ZN 8 Zone 8 and 16 sensor loop input (+).

These terminals are used to connect the

telephone line from the street.

OUT

These terminals are used to connect the

premises telephones.

Table 4: Terminal Block Descriptions

Note

The maximum combined continuous current draw

from the +12V, LAN + and COMM+ terminals must

not exceed 1 Amp

Bo ard Co nne c tor s

Connector Description

Service

This socket allow you to connect a service

Keypad to the panel during installation.

Tamper

This socket is used to connect the cabinet

tamper switch to the panel.

Default

This push button is used to reset the con-

trol panel back to factory default and to

enable Direct Link Programming Mode.

Voice

Module

This is used to connect the optional Voice

Command Module (CM100).

Direct Link

Port

This socket is used to connect the Direct

Link Interface (P/N CM900) or the Flash

Programmer Interface (P/N CM901) to the

panel.

Telco

This is a RJ12 6P/4C connector that allows

you to connect the control panel to the

PSTN telephone line.

Expansion

Port

Used to connect addition modules to the

control panel. eg TCP/IP interface.

LAN Term Used to terminate the RS485 LAN.

Table 5: Board Connector Descriptions

ABOUT THE KEYPAD

The ICON Keypad has 20 keys or buttons. The buttons allow

you to input instructions and navigate the menu screens

as required. Some buttons have a secondary function

which is activated by holding them down for two seconds.

Each button’s function is described below.

Keypad Button Fun c tions

Key Description

The numeric keys allow you to enter

numbers when required.

Use the [MENU] and the numeric keys

to enter commands. The [MENU] key

is also used to go back one level when

navigating through menus or to exit a

programming location without saving

changes.

The [ON] key allows you to turn an area

or output on. To turn all areas on at the

same time when the system has been

partitioned, press and hold the [ON]

key for two seconds.

The [PART] key allows you to turn an

area Part On. This key can also be used

to bypass a zone or multiple zones when

you press and hold for two seconds.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Bosch Solution 16i Spécifications Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch Solution 16i