Bosch LTC 8500 Manuel d'instructions Page 90
- Page / 104
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EN | 80 Bosch Security Systems | December 13, 2005
site switcher. The control data line should be connected to a LTC 8780 Series Data
Converter to provide address decoding functions for the satellite site. If operators at
the satellite site are permitted to control pan/tilt/zoom-equipped cameras, a
LTC 8569 Series Code Merger must be installed at the satellite site. The Code
Merger combines code generated by the main site and the satellite site, so both sites
have control over pan/tilt/zoom-equipped cameras located at the satellite site. The
LTC 878 0 Series unit can then be connected to one of the data outputs of the
LTC 8569 Series unit.
One or more monitor outputs from each satellite system are used as video trunk
lines to link the remote sites to the Main site. The number of trunk lines from a sat-
ellite site determines the maximum number of cameras from that site that may be
viewed simultaneously at the Main site. A satellite switcher model must be selected
so that it provides the desired number of local monitor outputs plus the number of
monitor outputs that will be used as trunk lines.
The Main site switcher must include sufficient camera inputs for local cameras plus
trunk lines. The maximum physical number of camera inputs or monitor outputs
used as trunk lines cannot exceed the capacity of the system. A single Main site
switcher can control multiple satellite sites up to its video input limit. If full matrix
switching is required at the Main site, the number of trunk lines from each satellite
site must equal the number of monitors connected to the Main site switcher. Multi-
ple independently controlled Main site systems can be combined to provide large
numbers of monitor outputs at the Main site. System capacities are listed below:
Since Main site Allegiant Series switchers support access to a large quantity of
remote satellite cameras, they provide additional logical camera numbers for identi-
fying the location of the satellite camera inputs in the system. These logical camera
numbers can also include titles which would appear on the Main site's monitors for
any remote cameras. Since each camera (anywhere in the system) must have a
unique camera number, logical camera numbers together with physical camera
inputs make up the total system camera capacity. Thus, there is a trade-off between
the total number of Main site cameras and the number of inputs used as trunk lines.
The more inputs used as trunk lines, the fewer there are for use as direct camera
inputs.
System Type
Max. Camera
Inputs
Max. Monitor
Outputs
Max. No. of
Satellite Sites
LTC 8100 Series 8 2 8
LTC 8 20 0 S e ries 16 5 16
LTC 8 30 0 Seri es 32 6 32
LTC 8 50 0 Seri es 64 8 64
LTC 8 6 00 Series 128 16 128
LTC 8 8 00 Series 256 64 256
LTC 8 9 00 Series 4096 512 256
Model No. Maximum Number System Cameras*
LTC 8100 Series 264
LTC 8200 Seri e s 272
LTC 8 30 0 Series 288
LTC 8 50 0 Series 320
LTC 8 6 00 Series 1152
LTC 8 8 00 Series 2304
LTC 8 9 00 Series 4608
*Camera inputs at all sites, plus trunk lines.
- LTC 8500 Series 1
- Important Safeguards 3
- Safety Precautions 4
- Sécurité 5
- Sicherheitshinweise 5
- Precauciones de Seguridad 5
- Veiligheidsmaatregelen 6
- Sicurezza 6
- Medidas de Segurança 6
- 1Unpacking 11
- 2Service 12
- 3Description 13
- 5System Components 17
- 6System Accessory Components 18
- 6.5 LTC 8555 Series Keyboards 19
- 6.9 AutoDome Series 19
- Integration Server 22
- 6.23 Logging Printer 24
- Logging Printer 25
- 7Installation Procedure 26
- 7. 3Video Output Modules 27
- 7. 4CPU Module 27
- Baud rate -- 19,200 29
- Stop bits -- 1 29
- Data bits -- 8 29
- Parity -- None 29
- Central 31
- Control 31
- Configurations 35
- 10 Feature Selection 37
- 11 Main Power Connections 38
- 12 Video Monitor Display 39
- System Status Display 40
- 13 Factory Default Settings 43
- Lower CPU DIP Switch S1002 44
- S1002 DIP Switch Function 44
- Stop Bits 1 1 1 47
- Data Bits 8 8 8 47
- Parity None None None 47
- Handshake Yes No No 47
- 14 User Information 48
- 15 Alarm Information 50
- 15.6 Sample Alarm Responses 51
- Sequence & Display Mode 52
- 15.7 Alarm Relay Response 53
- 16 Keyboard Operation 54
- 16.3 Switcher Commands 55
- 16.5 Alarm Commands 57
- 16.6 Sequence Control 58
- Run a Sequence 59
- Stop a Running Sequence 59
- 16.7 Sequence Programming 60
- Sequence Function Summary 61
- 17 Keyb oard User Functions 63
- User Function 7 - Set Time 67
- User Function 8 - Set Date 67
- 18 Maintenance Information 75
- 18.3 AC Line Fuse Replacement 76
- 20 Error Messages 80
- 21 Troubleshooting Guide 83
- 21.5 No Alarm Response 84
- 22 Glossary of Terms 86
- Appendix A Satellite Systems 88
- Monitor 92
- Output(s) 92
- Input(s) 92
- CPU Software Version Numbers 93
- C.1 Main Bay Video 96
- C.2 Keyboards 96
- C.3 Alarm Interface Unit 96
- C.4 Signal Distribution Unit 97
- C.5 Receiver/Drivers 97
- Console Port RS-232 Pin-outs 98
- Alarm Port RS-232 Pin-outs 98
- Keyboard RS-485 Ports 98
- Printer Port RS-232 Pin-outs 98
- Code Port Pin-outs 99
- COMM PORT 1 and COMM PORT 2 99
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch LTC 8500
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels