Bosch LTC 8500 Manuel d'instructions Page 29
- Page / 104
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
General Accessory Installation
EN | 19
8Optional Accessories Installation
8.1 General Accessory Installation
There are many accessory products available for the Allegiant Series, including key-
boards, alarm interface units, control code signal distribution units, etc. If applicable,
these products can be installed at the same time as the main CPU bay installation,
or postponed until later. In some cases, products are designed to be racked in close
proximity to the main CPU bay, so appropriate rack space should be reserved.
Please refer to the instructions supplied with the specific accessory product for com-
plete installation details.
8.2 Logging Printer Option Installation
NOTE Although the exact installation procedure for each printer varies, the following
steps are generally required. Be sure to save the printer reference manual for
procedures not covered.
1. Switch the main power OFF to the printer.
2. Install the ribbon cartridge and paper if necessary.
3. Set any configuration switches for your particular printer to match the format
provided by the Allegiant system. Note that the system communication protocol
can be changed using the Keyboard User Functions (described later in this man-
ual) with the optional Allegiant LTC 8059 MCS package. The factory default
values are as follows:
NOTE The required interconnect cable utilizes a custom pinout. Refer to the Appendix
Section of this manual for wiring details.
4. Attach the 25-pin male D-type connector side of the RS-232 cable to the con-
nector on the printer.
5. Attach the 9-pin male connector side of the cable to the Allegiant CPU bay con-
nector marked “PRINTER”.
6. Apply power to the printer.
7. Ve r i f y l o g g ing printer action by ‘loading’ a previously stored sequence into a
monitor, activating an alarm, or performing a system reset. Any of these actions
should cause printouts to occur.
Baud rate -- 19,200
Stop bits -- 1
Data bits -- 8
Parity -- None
- LTC 8500 Series 1
- Important Safeguards 3
- Safety Precautions 4
- Sécurité 5
- Sicherheitshinweise 5
- Precauciones de Seguridad 5
- Veiligheidsmaatregelen 6
- Sicurezza 6
- Medidas de Segurança 6
- 1Unpacking 11
- 2Service 12
- 3Description 13
- 5System Components 17
- 6System Accessory Components 18
- 6.5 LTC 8555 Series Keyboards 19
- 6.9 AutoDome Series 19
- Integration Server 22
- 6.23 Logging Printer 24
- Logging Printer 25
- 7Installation Procedure 26
- 7. 3Video Output Modules 27
- 7. 4CPU Module 27
- Baud rate -- 19,200 29
- Stop bits -- 1 29
- Data bits -- 8 29
- Parity -- None 29
- Central 31
- Control 31
- Configurations 35
- 10 Feature Selection 37
- 11 Main Power Connections 38
- 12 Video Monitor Display 39
- System Status Display 40
- 13 Factory Default Settings 43
- Lower CPU DIP Switch S1002 44
- S1002 DIP Switch Function 44
- Stop Bits 1 1 1 47
- Data Bits 8 8 8 47
- Parity None None None 47
- Handshake Yes No No 47
- 14 User Information 48
- 15 Alarm Information 50
- 15.6 Sample Alarm Responses 51
- Sequence & Display Mode 52
- 15.7 Alarm Relay Response 53
- 16 Keyboard Operation 54
- 16.3 Switcher Commands 55
- 16.5 Alarm Commands 57
- 16.6 Sequence Control 58
- Run a Sequence 59
- Stop a Running Sequence 59
- 16.7 Sequence Programming 60
- Sequence Function Summary 61
- 17 Keyb oard User Functions 63
- User Function 7 - Set Time 67
- User Function 8 - Set Date 67
- 18 Maintenance Information 75
- 18.3 AC Line Fuse Replacement 76
- 20 Error Messages 80
- 21 Troubleshooting Guide 83
- 21.5 No Alarm Response 84
- 22 Glossary of Terms 86
- Appendix A Satellite Systems 88
- Monitor 92
- Output(s) 92
- Input(s) 92
- CPU Software Version Numbers 93
- C.1 Main Bay Video 96
- C.2 Keyboards 96
- C.3 Alarm Interface Unit 96
- C.4 Signal Distribution Unit 97
- C.5 Receiver/Drivers 97
- Console Port RS-232 Pin-outs 98
- Alarm Port RS-232 Pin-outs 98
- Keyboard RS-485 Ports 98
- Printer Port RS-232 Pin-outs 98
- Code Port Pin-outs 99
- COMM PORT 1 and COMM PORT 2 99
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch LTC 8500
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.444 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels