Bosch LTC 8500 Manuel d'instructions Page 71
- Page / 104
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
General Information
EN | 61
User Function 28 - Select Console Log-in
This function controls the system's external console port log-in feature. After enter-
ing the mode, move the joystick up or down to select the mode in which the system
should function. If the log-in feature is enabled (MUST USE CON PWD is selected),
any external PC or other computing device will be required to log-in to communi-
cate with the system. External computing devices are required to enter a user num-
ber and correct password. If the console log-in feature is disabled (NO CON PWD
LOGIN is selected), the console port is available for communication.
Once the selection is made, exit the User Function mode and reset the system, either
via keyboard User Function 15 or by removing and restoring the main AC power to
the system. Once the system has been reset, the console log-in function is active, and
all external computing devices need to log-in to access the system.
User Function 29 - Reset RS-232 Parameters to Default
This function returns the system's external RS-232 ports to a known default state.
After entering the mode, enter a valid password. The system will reset after placing
the RS-232 protocols back to the default state. See Chapter 13, “Factory Default Set-
tings,” on page 33 for additional information.
User Function 30 - Set Console RS-232 Parameters
This function is used to set the RS-232 baud rate and handshake options for the sys-
tem's console port. Upon entry to this mode, the current settings are displayed.
Move the joystick up/down to select the baud rate, and left/right to select the hand-
shake option. After being changed, the port is also automatically set to eight data
bits, no parity, and one stop bit. Once new settings have been selected, enter the
user password and press [Enter]. If using the LTC 8555 Series keyboard, press
[User] to exit.
User Function 31 - Set Printer RS-232 Parameters
This function is used to set the RS-232 baud rate and handshake options for the sys-
tem's printer port. Upon entry to the mode, the current settings are displayed. Move
the joystick up/down to select the baud rate, and left/right to select the handshake
option. After being changed, the port is also automatically set to eight data bits, no
parity, and one stop bit. Once new settings have been selected, enter the user pass-
word and press [Enter]. If using the LTC 8555 Series keyboard, press [User] to exit.
User Function 32 - Set Alarm RS-232 Parameters
Use this function to select the RS-232 baud rate and handshake options for the sys-
tem's alarm port. Upon first entering the mode, the current settings will be dis-
played. Moving the joystick up/down selects the baud rate. Moving the joystick left/
right selects the handshake option. After being changed, the port is also automati-
cally set to eight (8) data bits, no parity, and one stop bit. Once the new settings
have been selected, enter the user password and press [Enter]. Press [User] to exit
the mode.
User Function 33 - Display User Number and Priority
This function displays the current user's number and priority level on the monitor
screen. The user number will be displayed on the top line and the user's priority
level will be displayed on the bottom line of the monitor screen. If using the
LTC 8555 Series keyboard, press [User] to exit.
- LTC 8500 Series 1
- Important Safeguards 3
- Safety Precautions 4
- Sécurité 5
- Sicherheitshinweise 5
- Precauciones de Seguridad 5
- Veiligheidsmaatregelen 6
- Sicurezza 6
- Medidas de Segurança 6
- 1Unpacking 11
- 2Service 12
- 3Description 13
- 5System Components 17
- 6System Accessory Components 18
- 6.5 LTC 8555 Series Keyboards 19
- 6.9 AutoDome Series 19
- Integration Server 22
- 6.23 Logging Printer 24
- Logging Printer 25
- 7Installation Procedure 26
- 7. 3Video Output Modules 27
- 7. 4CPU Module 27
- Baud rate -- 19,200 29
- Stop bits -- 1 29
- Data bits -- 8 29
- Parity -- None 29
- Central 31
- Control 31
- Configurations 35
- 10 Feature Selection 37
- 11 Main Power Connections 38
- 12 Video Monitor Display 39
- System Status Display 40
- 13 Factory Default Settings 43
- Lower CPU DIP Switch S1002 44
- S1002 DIP Switch Function 44
- Stop Bits 1 1 1 47
- Data Bits 8 8 8 47
- Parity None None None 47
- Handshake Yes No No 47
- 14 User Information 48
- 15 Alarm Information 50
- 15.6 Sample Alarm Responses 51
- Sequence & Display Mode 52
- 15.7 Alarm Relay Response 53
- 16 Keyboard Operation 54
- 16.3 Switcher Commands 55
- 16.5 Alarm Commands 57
- 16.6 Sequence Control 58
- Run a Sequence 59
- Stop a Running Sequence 59
- 16.7 Sequence Programming 60
- Sequence Function Summary 61
- 17 Keyb oard User Functions 63
- User Function 7 - Set Time 67
- User Function 8 - Set Date 67
- 18 Maintenance Information 75
- 18.3 AC Line Fuse Replacement 76
- 20 Error Messages 80
- 21 Troubleshooting Guide 83
- 21.5 No Alarm Response 84
- 22 Glossary of Terms 86
- Appendix A Satellite Systems 88
- Monitor 92
- Output(s) 92
- Input(s) 92
- CPU Software Version Numbers 93
- C.1 Main Bay Video 96
- C.2 Keyboards 96
- C.3 Alarm Interface Unit 96
- C.4 Signal Distribution Unit 97
- C.5 Receiver/Drivers 97
- Console Port RS-232 Pin-outs 98
- Alarm Port RS-232 Pin-outs 98
- Keyboard RS-485 Ports 98
- Printer Port RS-232 Pin-outs 98
- Code Port Pin-outs 99
- COMM PORT 1 and COMM PORT 2 99
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch LTC 8500
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.140 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels