Bosch LTC 8500 Manuel d'instructions Page 26
- Page / 104
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EN | 16 Bosch Security Systems | December 13, 2005
7Installation Procedure
7.1 M a i n C P U B a y I n s t a l l a t i o n
Before discarding the shipping cartons, verify that the various pieces of equipment
have no evidence of carrier damage.
CAUTION Do not apply power to the equipment until instructed to do so.
1. Remove the front panel of the main CPU bay by loosening the four (4) corner
fasteners.
2. Install the power supply in far right position of the main CPU bay insuring
proper alignment and seating of the module into the rear mating connector. Ver-
ify that the power supply ON/OFF switch is in the OFF position.
3. Install the four (4) screws and star washers (supplied) on the rear panel of the
bay(s) surrounding the power supply line cord to fasten the power supply
securely in place.
CAUTION If the Allegiant card cage is to be transported, the main power supply should be
removed to prevent possible damage to the bay's internal parts.
4. If the bay(s) are to be installed into a standard 19-inch EIA rack, remove the
four (4) rubber bumper foot pads found on the bottom of the bay before install-
ing the unit in the rack. Four (4) holes are provided for mounting the bay(s) in
the rack.
7. 2Video Input Modules
Te r m i n at ion switches on the Video Input Modules (VIM) must be set to the correct
position prior to installation. If necessary, see Section 7.6 “Termination Practices,” on
page 18 prior to actually installing the VIM on this system.
The appropriate number of VIMs should be installed in the main bay starting with
the left most slot. If less than full capacity is being used, the modules should be
inserted in a left-to-right manner so that the lower camera numbers are used first.
Figure 3: Typical Video Input Module Insertion
The VIMs are identical and are interchangeable within the designated VIM slots
without having to make any changes to the module.
- LTC 8500 Series 1
- Important Safeguards 3
- Safety Precautions 4
- Sécurité 5
- Sicherheitshinweise 5
- Precauciones de Seguridad 5
- Veiligheidsmaatregelen 6
- Sicurezza 6
- Medidas de Segurança 6
- 1Unpacking 11
- 2Service 12
- 3Description 13
- 5System Components 17
- 6System Accessory Components 18
- 6.5 LTC 8555 Series Keyboards 19
- 6.9 AutoDome Series 19
- Integration Server 22
- 6.23 Logging Printer 24
- Logging Printer 25
- 7Installation Procedure 26
- 7. 3Video Output Modules 27
- 7. 4CPU Module 27
- Baud rate -- 19,200 29
- Stop bits -- 1 29
- Data bits -- 8 29
- Parity -- None 29
- Central 31
- Control 31
- Configurations 35
- 10 Feature Selection 37
- 11 Main Power Connections 38
- 12 Video Monitor Display 39
- System Status Display 40
- 13 Factory Default Settings 43
- Lower CPU DIP Switch S1002 44
- S1002 DIP Switch Function 44
- Stop Bits 1 1 1 47
- Data Bits 8 8 8 47
- Parity None None None 47
- Handshake Yes No No 47
- 14 User Information 48
- 15 Alarm Information 50
- 15.6 Sample Alarm Responses 51
- Sequence & Display Mode 52
- 15.7 Alarm Relay Response 53
- 16 Keyboard Operation 54
- 16.3 Switcher Commands 55
- 16.5 Alarm Commands 57
- 16.6 Sequence Control 58
- Run a Sequence 59
- Stop a Running Sequence 59
- 16.7 Sequence Programming 60
- Sequence Function Summary 61
- 17 Keyb oard User Functions 63
- User Function 7 - Set Time 67
- User Function 8 - Set Date 67
- 18 Maintenance Information 75
- 18.3 AC Line Fuse Replacement 76
- 20 Error Messages 80
- 21 Troubleshooting Guide 83
- 21.5 No Alarm Response 84
- 22 Glossary of Terms 86
- Appendix A Satellite Systems 88
- Monitor 92
- Output(s) 92
- Input(s) 92
- CPU Software Version Numbers 93
- C.1 Main Bay Video 96
- C.2 Keyboards 96
- C.3 Alarm Interface Unit 96
- C.4 Signal Distribution Unit 97
- C.5 Receiver/Drivers 97
- Console Port RS-232 Pin-outs 98
- Alarm Port RS-232 Pin-outs 98
- Keyboard RS-485 Ports 98
- Printer Port RS-232 Pin-outs 98
- Code Port Pin-outs 99
- COMM PORT 1 and COMM PORT 2 99
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch LTC 8500
(20 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.435 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels