Bosch 11 KW Manuel d'instructions télécharger pdf (Page 45)

SETTINGS

6 720 806 768 (2013/02) 45

>>> Room temperature during time program

▶ Set the temperature that should apply as exceptional temperature in

the program.

The menu is displayed only if Program 1or Program 2has been

selected.

>>> Copy to all heating circuits

▶Select Yes to have the same control for all installed circuits.

The menu is displayed only under Circuit 1.

Room temperature program when there is no room controller:

>> Room temperature program

>>> Active program

>>> View/edit active program

The same as when there is a room controller, see above.

>>> Room temperature normal

▶ Set the measured value in the room.

The indicated value is used by temperature programs to calculate the

difference between normal and exceptional temperature.

>>> Temperature increase/decrease

▶ Use this function to adjust the room temperature so that the normal

room temperature (see the previous menu) becomes the desired

temperature.

▶ Use this function to simply increase or decrease the heat when there

are no room controllers.

– – gives approx. 1 °C lower room temperature.

– gives approx. 0.5 °C lower room temperature.

+ gives approx. 0.5 °C higher room temperature.

++ gives approx. 1 °C higher room temperature.

>>> Setting temp. increase/decrease

>>>> Limit value for left or right end point

▶ Set which outdoor temperature should be the limit value for the end

point that should be adjusted when increase/decrease is requested.

At outdoor temperatures lower than the limit value, the flow

temperature in the right end point (-35 °C) of the heat curve is

affected, with change indicated in %, see below.

At outdoor temperatures higher than the limit value, the flow

temperature in the left end point (+20 °C) of the heat curve is

affected, with change indicated in %, see below.

>>>> Change when much colder/warmer

▶ Set how much % the flow temperature in the applicable end point of

the heat curve should change down or up when – – or ++ is selected

in Temperature increase/decrease.

>>>> Change when colder/warmer

▶ Set how much % the flow temperature in the applicable end point of

the heat curve should change down or up when – or + is selected in

Temperature increase/decrease.

>>> Room temperature influence

Set in the same way as in menu Room sensor (room controller)

( Chapter 20.1). The setting is used in the temperature program to

calculate how the flow line temperature is affected when Room

temperature exception is to apply.

>>> Room temperature during time program

>>> Copy to all heating circuits

The same as when there is a room controller, see above.

> Circuit 2, 3...

Make the settings for the first mixed circuit under Circuit 2. Other

circuits are displayed only if they exist. The same functions apply to

these as the functions for circuit 2.

>> Mixing valve mode

▶Select Off if the circuit is not ready or needs to be turned off

temporarily or should not be used.

>> Type of heating system

▶ Select type of heating system.

The factory settings for the Radiator have a curve value (flow

temperature) of 22 °C at 20 °C an outdoor temperature, 37.4 °C at –

2.5 °C and 60 °C at -35 °C at an outdoor temperature (the high point of

the curve).

The factory settings for the Underfloor have a curve value (flow

temperature) of 22 °C at 20 °C outdoor temperature, 27.2 °C at -2.5°C

and 35 °C at -35 °C outdoor temperature.

Factory setting 17.0 °C

Lowest value 10.0 °C

Highest value 30.0 °C

Table 51 Room temperature, exception

Factory setting No

Alternative No/Yes

Table 52 All circuits

Factory setting 20.0 °C

Lowest value 10.0 °C

Highest value 35.0 °C

Table 53 Room temperature, normal

Factory setting =

Alternative – – , – , =, +, ++

Table 54 Room temperature increase/decrease

Factory setting 0.0 °C

Lowest value -10.0 °C

Highest value 15.0 °C

Table 55 Heating increase/decrease limit value

Factory setting 8%

Lowest value 1%

Highest value 20%

Table 56 Change when much colder/warmer

Factory setting 3%

Lowest value 1%

Highest value 20%

Table 57 Change when colder/warmer

It always takes some time for a change of a heating

setting, e.g. an increase or decrease in room

temperature, to apply. The same applies in the event of a

quick change of the outdoor temperature. This is why

you should always wait for at least 24 hours before

making a new change.

Factory setting Off

Alternative Heating/Off

Table 58 Mixing valve operating mode

Factory setting Underfloor

Alternative Radiator/Underfloor

Table 59 Type of heating system

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 71 72

Commentaires sur ces manuels

Pas de commentaire

Bosch 11 KW Manuel d'instructions Page 45

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à chaleur Bosch 11 KW