Bosch AMAX panel 4000 EN Guide d'installation Page 61
- Page / 176
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11 - AC Power Supply Fault
This output operates when a AC MAINS fault occurs.
The output is reset:
1. When the AC power supply is restored and fault is reset.
2. When the output programmed duration is up.
If this duration is programmed as 000, the output will continue till the AC MAINS power is
restored and fault is reset.
12 - Low Battery
This output operates when a Low Battery fault occurs.
The Dynamic Battery Test is performed every 4 hours after the system is powered up and
every time the system is armed.
The output is reset:
1. Only after a Dynamic Battery Test report that the backup battery voltage is normal and
fault is reset.
2. When the output programmed duration is up.
If this duration is programmed as 000, the output will continue till battery is restored and fault
is reset.
13 - Tamper
This output operates when a Tamper condition occurs.
The output is reset:
1. When the output programmed duration is up.
lf this duration is programmed as 000, the output will continue till the Tamper condition is
Restored and Tamper is reset.
14 - External Fault
This output operates when an External Fault occurs.
The output is reset:
1. When the output programmed duration is up.
lf this duration is programmed as 000, the output will continue till the External Fault is
Restored and the fault is reset.
15 - All Faults
This output operates when a Fault occurs.
The output is reset:
1. When the output programmed duration is up.
lf this duration is programmed as 000, the output will continue till the Fault is Restored and
the fault is reset.
16 - Fire Alarm
The output is triggered when Fire Alarm.
17 - Fire Reset
The output is triggered when Fire Reset.
18 - AWAY Armed
This output operates when System is AWAY Armed.
The output is reset:
1. When the output programmed duration is up.
AMAX panel 4000 / AMAX panel 4000
EN
Settings | en 61
Bosch Sicherheitsysteme GmbH Installation Guide 2013.07 | 03 | F.01U.267.112
- Table of contents 3
- 4 en 4
- Table of Contents 5
- 6 en 6
- Graphics 7
- 8 en 8
- Short Information 9
- System overview 10
- Brief Introduction 11
- Address Setting 11
- Wiring and Installation 12
- Alarm Control Panel 13
- DIP Switch 16
- Status Indicator 16
- Installation 17
- Press latch 23
- Wall Tamper 24
- Address Jumper 26
- E N √ E N √ 29
- Backup Battery 30
- Installation 31
- Settings 32
- Receiver Subscriber ID Number 33
- Receiver Transmission Format 33
- 34 en 34
- Settings 35
- 36 en 36
- Settings 37
- Dual IP 38
- System Reporting 39
- Settings 41
- Settings 43
- 44 en 44
- Domestic Call 45
- Zone Inputs 46
- BBBBB7DPSHU6ZLWFK 47
- BBBBB=RQH6ZLWFK 47
- Settings 49
- Settings 51
- 52 en 52
- Settings 53
- Settings 55
- Adding and Changing Zone 57
- Onboard / Extension Output 58
- Output Events 58
- Settings 59
- Settings 61
- Output Options 63
- 64 en 64
- Settings 65
- 66 en 66
- Settings 69
- Settings 71
- Settings 73
- Settings 75
- Settings 77
- Common Area 78
- Area Delay 79
- Keypad Area 79
- Configuration 80
- User Code Commands 81
- LCD Keypad Menu Programming 82
- INSTALLER MENU 83
- COM+REPORT SETTING 84
- ZONE SETTING 85
- KP/AREA SETTING 86
- SYSTEM SETTING 87
- OUTPUT SETTING 88
- RF SETTING 89
- LED/LCD Keypad Programming 90
- PC Programming 91
- 92 en 92
- Direct Connection 93
- Figure 8.13: A-Link Plus 94
- Figure 8.14: Direct link port 94
- 94 en 94
- Modem Connection 95
- 96 en 96
- Configuration 97
- 98 en 98
- Figure 8.19: Modem Connect 99
- Configuration 99
- IP Connection 100
- Configuration 101
- 102 en 102
- Configuration 103
- Figure 8.23: Network Connect 104
- 104 en 104
- Configuration 105
- 106 en 106
- Programming 107
- 108 en 108
- Programming 109
- VDS-A EN=3 110
- VDS-A=0 110
- Programming 111
- 112 en 112
- Zone Programming 113
- 114 en 114
- Programming 115
- 116 en 116
- Programming 117
- 118 en 118
- Programming 119
- 120 en 120
- Programming 121
- 122 en 122
- Programming 123
- Output Programming 124
- Programming 125
- 126 en 126
- Programming 127
- 128 en 128
- Access Codes 129
- 130 en 130
- Programming 131
- 132 en 132
- Programming 133
- 134 en 134
- System Programming 135
- Programming 137
- 138 en 138
- Programming 139
- 140 en 140
- Programming 141
- 142 en 142
- Programming 143
- Programming 145
- 146 en 146
- Programming 147
- 148 en 148
- Table 9.6: Characters 149
- Programming 149
- 150 en 150
- Table 9.7: Assign Zone Names 151
- Programming 151
- 152 en 152
- Keypad Usage and Operations 153
- 1 2 3 … 157
- Arming the System 158
- Disarming the System 159
- 1 Accessory Module Failure 160
- Power Failure 160
- Bypassing Zones 163
- Change Individual Code 165
- Keypad Panic Alarm 165
- Keypad Fire Alarm 166
- Keypad Medical Alarm 166
- Troubleshooting 167
- 168 en 168
- Troubleshooting 169
- Maintenance12 170
- Technical Data 171
- 172 en 172
- Technical Data 173
- 174 en 174
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch AMAX panel 4000 EN
(94 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels