Bosch AMAX panel 4000 EN Guide d'installation Page 162
- Page / 176
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
c) To exit from Fault and Tamper Analysis Mode, press [#].
System Test
Siren Test
This function allows the code holders to test the siren.
a) Enter your Code + [4] [1] and press [#]. It beeps twice and the siren will be activated for 1
second.
Communication Test
This function allows the code holders to send a test report to a central monitoring station.
a) Enter your Code + [4] [2] and press [#]. It beeps twice and a test report is send.
The Keypad will display the status of the test report for all communication paths.
To exit the test report press [#].
Walk Test Mode
This function allows code holders to test detection devices to ensure they are functioning
correctly. Before activating Walk test Mode, bypass any zones that are not required for testing.
During the walk test, no walk test report is sent out to the control panel system.
How to enter into Walk Test Mode:
1. Enter your Code + [4] [3] and press [#]. It beeps twice and the STAY and AWAY indicators
flash.
2. Unseal and seal the zones to be tested. The keypad sounds one second beep and the
siren sounds one beep each time when a Zone status is changed.
To exit Walk test Mode:
1. Enter your Code + [4] [3] and press [#].
Event Log Recall Mode
This function allows code holders to playback the last 254 events saved in each event log on
the Text Keypad.
All Event Log here all events are logged
EN Event Log here only EN related events are logged
Dialer Event Log here only Dialer related events are logged
How to enter Event Log Recall modes:
All Event Log
Enter your code + [2] [2] and press[#]. It beeps twice.
EN Event Log
Enter your code + [2] [3] and press [#]. It beeps twice.
10.4
10.4.1
10.4.2
10.4.3
10.5
162 en | Keypad Usage and Operations
AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
- Table of contents 3
- 4 en 4
- Table of Contents 5
- 6 en 6
- Graphics 7
- 8 en 8
- Short Information 9
- System overview 10
- Brief Introduction 11
- Address Setting 11
- Wiring and Installation 12
- Alarm Control Panel 13
- DIP Switch 16
- Status Indicator 16
- Installation 17
- Press latch 23
- Wall Tamper 24
- Address Jumper 26
- E N √ E N √ 29
- Backup Battery 30
- Installation 31
- Settings 32
- Receiver Subscriber ID Number 33
- Receiver Transmission Format 33
- 34 en 34
- Settings 35
- 36 en 36
- Settings 37
- Dual IP 38
- System Reporting 39
- Settings 41
- Settings 43
- 44 en 44
- Domestic Call 45
- Zone Inputs 46
- BBBBB7DPSHU6ZLWFK 47
- BBBBB=RQH6ZLWFK 47
- Settings 49
- Settings 51
- 52 en 52
- Settings 53
- Settings 55
- Adding and Changing Zone 57
- Onboard / Extension Output 58
- Output Events 58
- Settings 59
- Settings 61
- Output Options 63
- 64 en 64
- Settings 65
- 66 en 66
- Settings 69
- Settings 71
- Settings 73
- Settings 75
- Settings 77
- Common Area 78
- Area Delay 79
- Keypad Area 79
- Configuration 80
- User Code Commands 81
- LCD Keypad Menu Programming 82
- INSTALLER MENU 83
- COM+REPORT SETTING 84
- ZONE SETTING 85
- KP/AREA SETTING 86
- SYSTEM SETTING 87
- OUTPUT SETTING 88
- RF SETTING 89
- LED/LCD Keypad Programming 90
- PC Programming 91
- 92 en 92
- Direct Connection 93
- Figure 8.13: A-Link Plus 94
- Figure 8.14: Direct link port 94
- 94 en 94
- Modem Connection 95
- 96 en 96
- Configuration 97
- 98 en 98
- Figure 8.19: Modem Connect 99
- Configuration 99
- IP Connection 100
- Configuration 101
- 102 en 102
- Configuration 103
- Figure 8.23: Network Connect 104
- 104 en 104
- Configuration 105
- 106 en 106
- Programming 107
- 108 en 108
- Programming 109
- VDS-A EN=3 110
- VDS-A=0 110
- Programming 111
- 112 en 112
- Zone Programming 113
- 114 en 114
- Programming 115
- 116 en 116
- Programming 117
- 118 en 118
- Programming 119
- 120 en 120
- Programming 121
- 122 en 122
- Programming 123
- Output Programming 124
- Programming 125
- 126 en 126
- Programming 127
- 128 en 128
- Access Codes 129
- 130 en 130
- Programming 131
- 132 en 132
- Programming 133
- 134 en 134
- System Programming 135
- Programming 137
- 138 en 138
- Programming 139
- 140 en 140
- Programming 141
- 142 en 142
- Programming 143
- Programming 145
- 146 en 146
- Programming 147
- 148 en 148
- Table 9.6: Characters 149
- Programming 149
- 150 en 150
- Table 9.7: Assign Zone Names 151
- Programming 151
- 152 en 152
- Keypad Usage and Operations 153
- 1 2 3 … 157
- Arming the System 158
- Disarming the System 159
- 1 Accessory Module Failure 160
- Power Failure 160
- Bypassing Zones 163
- Change Individual Code 165
- Keypad Panic Alarm 165
- Keypad Fire Alarm 166
- Keypad Medical Alarm 166
- Troubleshooting 167
- 168 en 168
- Troubleshooting 169
- Maintenance12 170
- Technical Data 171
- 172 en 172
- Technical Data 173
- 174 en 174
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch AMAX panel 4000 EN
(94 pages)
(24 pages)
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels