Bosch D720 Guide d'installation télécharger pdf (Page 15)

D9412GV3/D7412GV3 | Operation and Installation Guide | 4.0 Installation

Bosch Security Systems, Inc. | 2/10 | F01U143070-01 15

3.3.12 Event Log

The system stores from 500 to 1000 events and event

modifiers from all areas in its event log. Event

modifiers add information about an event to the log.

Some events are always followed by a modifier. For

example, the system adds at least two items to the

log each time an area is armed or disarmed, the Open

(or Close) event and an event modifier showing the

previous arming state.

All events and their modifiers can be stored even if

the control panel does not send a report for them. The

log can be viewed at a keypad, printed locally using

the D9131A Parallel Printer Interface Module and a

parallel printer, or uploaded using Remote

Programming Software (RPS).

For a list of the log events and event modifiers, refer

to the appendix in the user’s guide for the keypad.

3.3.13 Ground Fault Detection

The Earth Ground Terminal on the control panels is

electrically isolated from all other terminals to allow

the D9412GV3 and the D7412GV3 to detect ground

fault conditions. A Ground Fault Detect Enable switch

(S4) is located just under Terminal 10, Earth Ground,

on the control panel. Refer to Section 4.5.2 Ground

Fault Detect Enable on page 17 for information on

operating this function.

3.3.14 Ground Fault Detection Added Feature

When Ground Fault Detect is enabled (S4 closed),

Points 1 to 8 can be used for non-powered fire-

initiating devices such as heat detectors, four-wire

smoke detectors, and pull stations. A D125B Powered

Loop Interface or a D129 Dual Class A Interface

Module is not required when connecting the non-

powered fire-initiating devices to Points 1 to 8.

3.3.15 Conettix Functions

The D6600 Conettix System supports data network

communications. Conettix allows the D6600 receiver

to connect to network topologies, specifically

Ethernet. Conettix also allows this receiver to process

messages to and from most networks using TCP/IP

protocols. Connecting to a data network is possible

using the COM4 or COM1 connection from the D6600

receiver to the D6680 Network Adapter. Alarm control

panels can send reports through telephone lines or

Ethernet and token-ring data networks to the D6600

receiver and then to the central station automation

software or the network printer through a local area

network (LAN) or wide area network (WAN). The

network can monitor the status of alarm control

panels.

3.3.16 Programming

Use the Bosch Security Systems D5200 Programmer

or the Remote Programming Software (RPS) to

program the D9412GV3 and D7412GV3 Control

Panels. Refer to the D9412GV3/D7412GV3 Program

Entry Guide (P/N: F01U143071) for programming

options.

3.3.17 Other Features

D9412GV3 and D7412GV3 Control Panels have

many programmable features. Some of the features

are listed below. Complete details on all features are

in the D9412GV3/D7412GV3 Program Entry Guide

(P/N: F01U143071).

• Supervision of AC (primary power), battery

(secondary power), Zonex and SDI buses, central

processing unit (CPU), up to three printers, and

two telephone lines

• Automatic System Test Reports

• Remote access for programming, diagnostics,

and log uploads using the remote programming

software (RPS)

• Fire alarm verification

• Programmable alarm output

• Programmable relay output using the D8129

OctoRelay Module

• Opening and closing windows

• Skeds (scheduled events)

4.0 Installation

4.1 Installation Preparation

This section contains a general installation procedure

and refers to other sections of the document for

detailed instructions.

Review this document and the D9412GV3/D7412GV3

Program Entry Guide (P/N: F01U143071) before

beginning the installation to determine the hardware

and wiring requirements for the features used.

Have the following documentation available when

reading through this guide:

• D9412GV3/D7412GV3 Program Record Sheet

(P/N: F01U143072)

• Security System Owner’s Manual

(P/N: 71-06633-000) and GV3 Series Owner’s

Manual Supplement (P/N: F01U143082)

• Installation manual for keypad or annunciator

(D1255 all models, D1255RB, D1256, D1256RB,

D1257, D1257RB, D1260 all models, or D720 all

models)

Before installation, become familiar with the operation

of the D5200 Programmer or the RPS.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Bosch D720 Guide d'installation Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Claviers numériques Bosch D720