Bosch 150 AC Spécifications Page 23
- Page / 146
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
• DOK-DIAX01-MAIN+2AD+1M-ANW1-EN-E1,44 • 07.97
23
1. Commissioning INDRAMAT AC Main Spindle Drives
1.5 Main Spindle Drives with RAC Controllers
1.5.1 Mains Requirements
Before switching on each time, check that the following mains requirements
are met:
• For 380V type: (type code field „AC supply voltage“=380)
3 x 400V +6% -15% 50 to 60 Hz
• For 460V type: (type code field „AC supply voltage“ = 460)
3 x 400V ±15%, 50 Hz or3 x 460V ±10%, 60 Hz
• mains-related earth
3 x 380V...460V ±10% 50 to 60 Hz
• mains-related earth
A transformer is not needed if the mains supply meets these conditions.
In the case of three-phase supplies with mains-related earth, conductor
but with phase-phase voltages other than those stated above, an
autotransformer must be used for voltage matching.
With three-phase supplies without mains-related conductor but with
phase-phase voltages meeting the above requirements, no isolating
transformer is necessary if the mains meets special conditions and the
RAC is protected by overvoltage protection devices (see "Electrical
Connections").
With three-phase supplies without mains-related earth conductor and
different mains voltages, a three-phase isolating transformer, with a
secondary voltage as stated above and a short-circuit voltage not
exceeding 4%, must be used. The neutral point of the secondary must
be connected to the system earth (see "Electrical Connections").
1.5.2 Checks with the Equipment Switched-Off
Compare the data on the equipment rating plates with the existing supply
voltage.
The details on the AS programming module must match the ratings of the
installed drive components, otherwise there is the risk of damage.
If a KDA 34.2 is to be operated with an RAC 2.2, then the KDA must be
designed for a supply voltage of 500 V (type code field "DC supply
voltage" = 500).
Check the wiring for short-circuits, breaks, incorrect connections,
conductor cross sections and compare with the Indramat connection
diagram.
• Earthing arrangements:
The earthing arrangements should be made as per the respective
Indramat connection diagrams. These should also include the rele-
vant protective measures for the machine. The earth connection
provides an operational earth with a protective function.
For RAC 2.2 and RAC 4.1
For RAC 3.1
Other mains supplies
Checking the installed drive
components
Condition of wiring
- Spindle Motors 1
- Overview of Sections 3
- About this documentation 5
- About this document 6
- Contents 10
- Spindle Drives 13
- INDRAMAT 15
- 1.2 Safety Guidelines 16
- 1.3 The Equipment Required 18
- Checking the drive 19
- Condition of wiring 19
- Cross sections of power 19
- Operating the drive with the 22
- Checking the speed/ 22
- 2. Operating the Controllers 27
- Operating mode switch 28
- R 5 3 1 2 1 29
- Switching into parameter 31
- Reading a parameter record 32
- Changing to another 32
- Display Definition 33
- Possible fault 35
- Possible fault messages 36
- 3. Controller Functions 37
- 3.2 Speed Command Value 38
- X2 control inputs 39
- Drehzahlsollwert 39
- Function conversion 41
- Speed limits 41
- Binary Coding 42
- Speed command value 42
- Floating-Point Coding 43
- Possible error message in 43
- Drehzahlsollwertrampen 45
- Instructions for using the 47
- Conversion formula (alterna 47
- 3.5 Command Value Smoothing 48
- Smoothing time constant 49
- 3.6 Spindle Positioning 50
- Spindelpos Standard 52
- Changing the direction of 53
- Direction of positioning 53
- 3600 spindle positions 54
- Entering position command 54
- Priority of the position 54
- Para-Spindel-3600 55
- Positioning accuracy 56
- Para-Spindel-refer 57
- Display: 59
- Torque build-up 62
- Ramp function 62
- Speed dependent 63
- Braking without overshoot 63
- P-GAIN data: 64
- of tacho filter: 64
- Follow-up time T 64
- of the speed controller: 64
- C-axis functions 65
- Conversion of functions 66
- Weighting conversion speed 66
- 3.9 Power and Torque Limits 67
- Limiting with parameter or 68
- Changeover capability of the 68
- A) Percentage torque 69
- B) Torque utilization related 70
- C) Power level related to 70
- General data on the 71
- D) Torque value 71
- Para-Analo 72
- X2 signal outputs 73
- Temperaturvorwarnun 74
- 0 = fault 76
- Umschaltung-Para 77
- Switchable function 78
- 3.15 Gear Change 79
- Gear stage dependent drive 80
- Functional sequence 81
- Possible error messages on 81
- Sequence of operations 84
- 3.16 Two-Motor Changeover 85
- Possible error messages in 86
- 3.17 Master-Slave Operation 88
- Slave drive data 89
- Formula: 90
- Para-NOT-AUS 93
- (KDA, TDA) 95
- OSCILATE 99
- N<NMIN 99
- POS ORDER 99
- 4.2 Fault Diagnostics 100
- RSKCURNT (RAC 3 only) 105
- S-CIRCUIT 105
- 5. Overview of Parameters 106
- Additions list ! 108
- Para-umschaltbar 109
- Additions list! 110
- Parameter protocol! 111
- Para-M03 113
- Parameter-Blatt 115
- X2 Control inputs 116
- Signal outputs 116
- Analogue outputs 116
- 19 and terminals 1 and 2 117
- (option) 118
- 1 = acceptance of current N 119
- 6.4 SERCOS Interface (option) 120
- X6 with KDA/TDA; X13 with RAC 121
- X6 with KDA/TDA 122
- X13 with RAC 122
- 6.7 Serial Interface (option) 123
- 6.8 Motor Feedback Connection 124
- ( 400 125
- mA ) 125
- 7. Index 126
- Anschlußplan für 82 129
- < > 137
- Type code fields: 139
- TDA 1.1 - 100 - 3 - A00 139
- Figure 121: Type codes for AS 143
- High-resolution 145
- Indramat 146
Produits connexes et manuels pour Outils électriques Bosch 150 AC
(12 pages)
(98 pages)
(104 pages)NEC EA274WMi Handbücher
Bedienungsanleitungen und Benutzerhandbücher für LED-Anzeigen NEC EA274WMi.
Wir stellen 1 PDF-Handbücher NEC EA274WMi zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Nec EA274WMi Bedienungsanleitung (27 Seiten)
Marke: Nec | Kategorie: LED displays | Größe: 2.69 MB |
Inhaltsverzeichnis
Contents
7
Controls
13
ECO TOOLS
14
*3 DualLink
17
MENU Tools
18
Information
19
OSD Warning
19
English-18
20
Features
21
Figure 3
24
Figure 4
24
Weitere Produkte und Handbücher für LED-Anzeigen NEC
| Modelle | Dokumententyp |
|---|---|
| LCD2090UXIBLK |
Datenblatt
NEC MultiSync® LCD2090UXi,
2 Seiten
|
| MD242C2 |
Spezifikationen
NEC MD242C2,
36 Seiten
|
| LCD175VXM+ |
Datenblatt
NEC MultiSync® LCD175VXM+,
17 Seiten
|
| EA224WMi |
Bedienungsanleitung
NEC EA224WMi,
26 Seiten
|
| EX231W |
Bedienungsanleitung
NEC EX231W,
21 Seiten
|
| EA223WM-WH |
Bedienungsanleitung
NEC EA223WM-WH,
25 Seiten
|
| 60001871 |
Datenblatt
NEC MultiSync LCD1990SX-BK,
2 Seiten
|
| 60001080HWLLIT |
Datenblatt
NEC MULTISYNC LCD2080UK+BK FLATPANEL TFT 20,1 INCH TBV HONEYWELL ITALY,
1 Seiten
|
| MDG5-BNDN1 |
Spezifikationen
NEC MD211G5 LED display,
22 Seiten
|
| E463 |
Bedienungsanleitung
NEC E323,
34 Seiten
|
| V322 |
Bedienungsanleitung
NEC V322,
42 Seiten
|
| MDG3-BNDA1 |
Spezifikationen
NEC MD211G3,
18 Seiten
|
| E201W |
Bedienungsanleitung
NEC E201W,
21 Seiten
|
| EA304WMi |
Bedienungsanleitung
NEC MultiSync EA304WMi,
28 Seiten
|
| EA243WM-BK |
Bedienungsanleitung
NEC EA243WM-BK LED display,
27 Seiten
|
| MDC3-BNDA1 |
Spezifikationen
NEC MD211C2,
35 Seiten
|
| EA222WME |
Bedienungsanleitung
NEC EA222WME,
22 Seiten
|
| EA244WMI-BK |
Bedienungsanleitung
NEC EA244WMI-BK,
26 Seiten
|
| P241W-BK |
Bedienungsanleitung
NEC P241W-BK,
34 Seiten
|
| AS231WM |
Bedienungsanleitung
NEC AS231WM,
17 Seiten
|
© 2020, manymanuals.fr. Tous droits réservés | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels