Bosch 150 AC Spécifications Page 102
- Page / 146
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
102
• DOK-DIAX01-MAIN+2AD+1M-ANW1-EN-E1,44 • 07.97
Cause:
The heatsink of the control unit has reached the cut-off temperature. The
TEMP WARN signal output (X2/9) has switched from 1 to 0.
Remedy:
With KK WARN, the drive must be perceptibly unloaded because a
further rise in temperature at the heatsink means the drive switches off
after 30 seconds!
Note: see Section 3.11
Cause:
The temperature of the motor windings has reached 155
o
C. The
TEMPWARN signal was ignored. The control unit has switched off.
Remedy:
Check motor fan, airways, load cycle and interconnections between the
TEMPWARN signal output and the controller. Reset required.
Note: see Section 3.11
Cause:
The motor has reached a temperature of 145°C. The TEMP WARN
signal output (X2/9) has switched from 1 to 0.
Remedy:
Check motor fan, airways and load cycle. Cancel the fault message with
the red accept key!
Note: see Section 3.11
Cause:
No motor contactor changeover acknowledgement.
Remedy:
Check the wiring for agreement with the connection diagram.
Note: see Section 3.16
Cause:
No command value interface card is inserted, or the one fitted is not
recognized.
Remedy:
Switch off the control unit. Check command value interface. Replace if
necessary. Contact Indramat customer service!
Cause:
No voltage at mains terminals L1,L2,L3 or voltage too low.
Remedy:
Check mains supply conditions!
Cause:
Software and equipment do not match.
Remedy:
Use correct programming module (AS4./...).
4. Diagnostics and Fault Clearance
KK WARN
MOT TEMP
MOT WARN
MOTOR 1/2
NO INPUT
NO MAINS
(RAC 3 only)
NO RAC 2.2
(RAC 2.1 only)
- Spindle Motors 1
- Overview of Sections 3
- About this documentation 5
- About this document 6
- Contents 10
- Spindle Drives 13
- INDRAMAT 15
- 1.2 Safety Guidelines 16
- 1.3 The Equipment Required 18
- Checking the drive 19
- Condition of wiring 19
- Cross sections of power 19
- Operating the drive with the 22
- Checking the speed/ 22
- 2. Operating the Controllers 27
- Operating mode switch 28
- R 5 3 1 2 1 29
- Switching into parameter 31
- Reading a parameter record 32
- Changing to another 32
- Display Definition 33
- Possible fault 35
- Possible fault messages 36
- 3. Controller Functions 37
- 3.2 Speed Command Value 38
- X2 control inputs 39
- Drehzahlsollwert 39
- Function conversion 41
- Speed limits 41
- Binary Coding 42
- Speed command value 42
- Floating-Point Coding 43
- Possible error message in 43
- Drehzahlsollwertrampen 45
- Instructions for using the 47
- Conversion formula (alterna 47
- 3.5 Command Value Smoothing 48
- Smoothing time constant 49
- 3.6 Spindle Positioning 50
- Spindelpos Standard 52
- Changing the direction of 53
- Direction of positioning 53
- 3600 spindle positions 54
- Entering position command 54
- Priority of the position 54
- Para-Spindel-3600 55
- Positioning accuracy 56
- Para-Spindel-refer 57
- Display: 59
- Torque build-up 62
- Ramp function 62
- Speed dependent 63
- Braking without overshoot 63
- P-GAIN data: 64
- of tacho filter: 64
- Follow-up time T 64
- of the speed controller: 64
- C-axis functions 65
- Conversion of functions 66
- Weighting conversion speed 66
- 3.9 Power and Torque Limits 67
- Limiting with parameter or 68
- Changeover capability of the 68
- A) Percentage torque 69
- B) Torque utilization related 70
- C) Power level related to 70
- General data on the 71
- D) Torque value 71
- Para-Analo 72
- X2 signal outputs 73
- Temperaturvorwarnun 74
- 0 = fault 76
- Umschaltung-Para 77
- Switchable function 78
- 3.15 Gear Change 79
- Gear stage dependent drive 80
- Functional sequence 81
- Possible error messages on 81
- Sequence of operations 84
- 3.16 Two-Motor Changeover 85
- Possible error messages in 86
- 3.17 Master-Slave Operation 88
- Slave drive data 89
- Formula: 90
- Para-NOT-AUS 93
- (KDA, TDA) 95
- OSCILATE 99
- N<NMIN 99
- POS ORDER 99
- 4.2 Fault Diagnostics 100
- RSKCURNT (RAC 3 only) 105
- S-CIRCUIT 105
- 5. Overview of Parameters 106
- Additions list ! 108
- Para-umschaltbar 109
- Additions list! 110
- Parameter protocol! 111
- Para-M03 113
- Parameter-Blatt 115
- X2 Control inputs 116
- Signal outputs 116
- Analogue outputs 116
- 19 and terminals 1 and 2 117
- (option) 118
- 1 = acceptance of current N 119
- 6.4 SERCOS Interface (option) 120
- X6 with KDA/TDA; X13 with RAC 121
- X6 with KDA/TDA 122
- X13 with RAC 122
- 6.7 Serial Interface (option) 123
- 6.8 Motor Feedback Connection 124
- ( 400 125
- mA ) 125
- 7. Index 126
- Anschlußplan für 82 129
- < > 137
- Type code fields: 139
- TDA 1.1 - 100 - 3 - A00 139
- Figure 121: Type codes for AS 143
- High-resolution 145
- Indramat 146
Produits connexes et manuels pour Outils électriques Bosch 150 AC
(104 pages)Samsung BQ1D4T023/XEC manuals
Owner’s manuals and user’s guides for Receiver Samsung BQ1D4T023/XEC.
We providing 1 pdf manuals Samsung BQ1D4T023/XEC for download free by document types: User Manual
Table of contents
More products and manuals for Receiver Samsung
| Models | Document Type |
|---|---|
| SAMSUNG WB800F |
User Manual
Samsung SAMSUNG WB700 Manual do usuário,
168 pages
|
| SGH-C260L |
User Manual
Samsung SGH-C260 Manual do usuário,
2 pages
|
| SGH-X510 |
User Manual
Samsung SGH-X510 Manual do usuário,
2 pages
|
| RC-6013 |
User Manual
Samsung VC-6014 Manual do usuário,
8 pages
|
| SAMSUNG MV800 |
User Manual
Samsung SAMSUNG MV800 Manual do usuário,
145 pages
|
| SGH-C520 |
User Manual
Samsung SGH-C520 Manual do usuário,
2 pages
|
| HW-C500 |
User Manual
Samsung HW-C500 Handleiding,
58 pages
|
| SAMSUNG ST30 |
User Manual
Samsung SAMSUNG ST30 Manual do usuário,
102 pages
|
| VC-5815V |
User Manual
Samsung VC-5815V Manual do usuário,
8 pages
|
| SGH-C300B |
User Manual
Samsung SGH-C300B Manual do usuário,
2 pages
|
| AV-R720 |
User Manual
Samsung AV-R720 Navodila za uporabo,
51 pages
|
| DIGIMAX 4500 SUPER |
User Manual
Samsung DIGIMAX V4 Manual do usuário,
140 pages
|
| SGH-C250 |
User Manual
Samsung SGH-C250 Manual do usuário,
2 pages
|
| NP-P50 |
User Manual
Samsung NP-P50 Manual do usuário,
188 pages
|
| HW-C500 |
User Manual
Samsung HW-C500 Kasutusjuhend,
58 pages
|
| WF90F5E5U4W/EP |
User Manual
Samsung WF90F5E5U4W/EP Manual do usuário [en] ,
44 pages
|
| HT-KP30 |
User Manual
Samsung HT-KP30 Руководство пользователя,
95 pages
|
| GT-I9023 |
User Manual
Samsung GT-I9023 Manual do usuário,
14 pages
|
| AV-R700 |
User Manual
 
Samsung AV-R700 Manuel utilisateur,
27 pages
|
| HW-C450 |
User Manual
Samsung HW-C450 Instrukcja obsługi,
20 pages
|
© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels