Bosch DS7445i Guide de l'utilisateur Page 35
- Page / 54
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DS7240/DS7220 User's Guide Copyright 2002 Detection Systems, Inc. P/N: 49211C Page 35
PART II: KEYPAD USER’S GUIDE: DS7445i LED KEYPAD
5.11 Bypass Zones
I can perform this function.
I cannot perform this function.
Key Sequence: [Bypass] Key or [#] + [0]
Description
Use this function to bypass one or more zones before
turning the system All On, On Perimeter Only or
Partial On. When a zone is bypassed, it can be
faulted without starting an alarm event.
Example: Your kitchen has just been painted and you
want to leave the windows open but still turn on the
system. Bypassing zones allows the system to be on
but prevents it from monitoring undesired areas.
Procedure
1. Make that the system is turned off (Armed and
Perimeter LEDs are off).
2. Enter a valid user PIN.
3. Press the [Bypass] key.
4. Enter the Zone Number that you want to bypass
followed by the [∗] key (for example, if you want
to bypass Zone 10, enter [1] + [0] + [∗]). Repeat
this step until all zones that must be bypassed
have been bypassed.
5. Press the [#] key to exit this function.
5.12 Date and Time
I can perform this function.
I cannot perform this function.
Key Sequence: [#] + [4] + [5]
Description
Use this function to program the system’s date and
time.
Procedure
1. Enter a valid user PIN.
2. Press [#] + [4] + [5].
3. The keypad turns the Zone 1 LED on.
On
Status
Power
Fire
Supervisory
Bell Silenced
Trouble
TEST WEEKLY
1 2 3 4 5 6 7 8
9 10 11 12 13
14 15
16
Zone 1 LED ON
Armed Perimeter
4. Enter the date and time using the MM/DD/YY,
HH:MM format.
The control panel may be configured to display
the date in International format (DD/MM/YY).
Check with your Security Company.
___
M
___
M
___
H
___
H
Month of
the year
Day of
the month
Current
Year
Hour of
the day
Minute of
the hour
/ ___
D
___
D
___
M
___
M
___
Y
___
Y
/ :
The keypad turns on Zone LEDs 1-6 (each LED
represents a digit to be entered) for the date and
Zone LEDs 1-4 for the time.
The time should be entered in 24-hour format (for
example, 8: 00 PM = 20:00).
5. After you enter the date and time, the keypad
sounds a long beep and automatically exits the
Date/Time function.
In the event of a power cycle (power is lost to
the system and then restored), the panel takes
the last event in the log and uses that as a
starting point for the time and date. It then
alerts you to enter the current time and date.
- User’s Guide for the 1
- MY ALARM COMPANY IS: 2
- Contents 3
- Part I: Introduction 4
- 3.0 Keypad Overview 5
- 3.2 Keypad Tones 6
- 3.3 Keypad LED Functions 6
- 3.4 Function Key Sequences 7
- 3.5 System Events 7
- 3.8 Logging Out of the System 7
- Part II: Keypad User’s Guide 8
- 4.7 Set Partial On Zones 10
- 4.10 Force Arming the System 12
- 4.11 View Faulted Zones 13
- 4.12 Bypass Zones 13
- 4.13 Date and Time 14
- 4.14 Change PIN 14
- 4.15 Change Others’ PINs 15
- 4.17 Add a PIN 16
- 4.18 Delete a PIN 17
- 4.19 Renew One-Time PINs 17
- 4.20 Check System Troubles 18
- 4.21 View Alarm Memory 18
- 4.22 View System Trouble 19
- 4.23 View Zone Trouble 19
- 4.24 System Test 19
- 4.25 Walk Test 20
- 4.26 Reset the System 21
- 4.27 Turn Chime On/Off 21
- 4.28 Select Chime Tone 21
- 4.29 Select Chime Zones 22
- 4.30 Extend Auto-On Time 22
- 4.31 Change Skeds 22
- 4.32 Change Outputs 25
- 4.33 Remote Program 26
- 4.34 All Areas Off 26
- 4.35 All Areas On 26
- 4.36 Move to Area 27
- 4.37 Auto-Forward On Setup 27
- 4.38 Auto-Forward Off Setup 28
- 4.39 Auto-Forward On/Off 28
- 4.41 View Log 29
- 5.1 Silence Alarms 30
- 5.2 Keypad Adjust 30
- 5.3 Turn the System Off 30
- 5.4 Turn the System All On 31
- 5.7 Set Partial On Zones 32
- Flashing Armed LED 33
- 5.10 Force Arming the System 34
- 5.11 Bypass Zones 35
- 5.12 Date and Time 35
- I can perform this function 36
- 5.17 Delete a PIN 39
- 5.18 Renew One-Time PINs 39
- 5.19 Check System Troubles 40
- 5.20 View Alarm Memory 40
- 5.21 View System Trouble 40
- 5.22 View Zone Trouble 41
- 5.23 System Test 41
- 5.24 Walk Test 42
- 5.25 Reset the System 42
- 5.26 Turn Chime On/Off 42
- 5.29 Extend Auto On Time 44
- 5.30 All Areas On 44
- 5.31 All Areas Off 44
- 5.32 Auto Forward On/Off 44
- 5.34 Remote Program 45
- Part III: Reference Materials 46
- 7.0 Panel Event Descriptions 47
- 10.0 Maintenance and Service 52
- 11.0 Power Failure 52
- 12.0 How to Clean the Keypad 52
- 13.0 Glossary 53
- Detection Systems, Inc. 6/02 54
- P/N: 49211C Page 54 of 54 54
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch DS7445i
(175 pages)
(44 pages)
(8 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels