Bosch D7212GV2 Guide d'installation télécharger pdf (Page 18)

D7212GV2 | Operation and Installation Guide | 4.0 Installation

18 Bosch Security Systems, Inc. | 2/07 | F01U003805-02

4.6.3 Installing Modules and Relays

1. Power down the unit by unplugging the

transformer and disconnecting the battery.

Always power down the unit when installing

modules or relays, or when making wiring

connections to the control panel.

2. Install and wire any modules required for the

installation as described in the module’s

installation instructions.

Instructions for the D8125 POPEX Module,

D8128D OctoPOPIT Module, D8129 OctoRelay

Module, and D811 Arm Status Relay Module

appear in this guide.

Refer to Section 9.0 Off-Board Points on page for

D8125 and D8128D instructions. Refer to Section

10.0 Off-Board Relays on page 44 for D8129 and

D811 instructions.

3. If using the power outputs at Terminals 7 or 8,

refer to Section 6.4 Programmable Power Output

Terminals 6, 7, and 8 on page 25 for instructions.

4.6.4 Connecting the On-board Points and

Keypads

Connect the on-board points and keypad wiring to the

system. Refer to Section 8.0 On-Board Points on page 29

and Section 11.0 Arming Devices on page 46 for

instructions.

4.6.5 Powering Up

Reconnect the battery, then plug in the transformer.

The buzzer sounds for two seconds when the control

panel is powered up. Leave the reset pin in the locked

position.

Yellow Charging Status LED Remains Lit: If the

yellow charging status LED remains lit after five

minutes of powering up the control panel, either the

battery is deeply discharged, or too many powered

devices were connected to the control panel.

Combined continuous current draw for Terminals 38,

24, and 32, and the accessory connector cannot exceed

1.4 A. Refer to Section 6.0 Power Outputs on page 25 for

help.

4.7 Programming the Control Panel

If the control panel is not already programmed, review

the D7212GV2 Program Entry Guide (P/N:

F01U003804). Ensure that all accessory modules for

desired features are available for installation. Place the

reset pin in the locked position to copy or send

information to and from the control panel.

Use the D5200 Programmer or the RPS to load a

custom program into the control panel.

Move the reset pin to the normal position (refer to

Figure 6 on page 17). The control panel sends Reboot

and Battery Reports to the receiver if programmed for

reporting

4.8 Installing the Point Chart Label

The point chart label is required for fire

systems with verifications points.

A point chart label is included in the literature pack.

Install the point chart label for fire or combined fire-

and-burglary systems that use verification points.

Use the D7212GV2 Program Record Sheet

(P/N: F01U003803) to gather the necessary information

for completing the point chart. Fill out the label and

install it on the inside of the enclosure door (refer to

Figure 2 on page 14).

Avoid smearing the entries on the chart.

Use the peel-off backing to press the label

in place.

4.9 Testing the System

After installing and programming the control panel,

test the system completely. Test the control panel and

all devices for proper operation.

Test after initially programming the control

panel and after subsequent programming

changes.

Refer to Section 4.10 Service Walk Test for complete

Service Walk Test instructions.

Clear after Test: To clear the event memory and

report buffer, momentarily close the reset pin. Events

stored in the control panel’s event log are not cleared.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Bosch D7212GV2 Guide d'installation Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch D7212GV2