Bosch ICP-CC488 Guide d'installation télécharger pdf (Page 71)

ICP-CC488 | Installation Guide | 16.0 Programmable Outputs EN | 71

Bosch Security Systems, Inc. | 12/08 | F01U089457-02

16.1 Redirecting Outputs to the

Codepad Buzzer

Multiple output event types can be directed to the

codepad buzzer so that the buzzer can indicate a

number of events.

To redirect an output to the codepad buzzer, select

an output and program it for the desired Output

Event Type. If the output is functioning correctly,

add 8 to the first (tens) digit of the Output Event

Type.

Example

3,0 Communications Failure

This event operates after the dialer makes all possible

attempts to reach the base station receiver. It is reset

when the panel receives the first Kiss-off. This

Output Event Type is not applicable to domestic

reporting.

To redirect this Output Event Type to operate a

codepad buzzer, program the Output Event Type as:

11,0 Communications Failure

The codepad buzzer operates instead of the output

that was programmed. Output 3 is no longer

functional and cannot be used for any other Output

Event Type.

16.2 Output Event Types

There are approximately 75 Output Event Types.

Two numbers designate each Output Event Type.

Program these numbers into the appropriate

locations for the output.

All reset times reference Polarity 1 and 8.

Reset times vary depending on the

selected polarity.

0,0 EDMSAT - Satellite Siren (Output 1 Only)

This output controls all functions of the SS914

Satellite Siren (EDMSAT). The Speaker Indication

Beeps option does not function through the satellite

siren for remote operations. No polarity is required

for this Output Event Type.

0,1 System Armed

This output operates when the system is armed. The

output is reset when the system is disarmed. If the

system is partitioned, this output operates when both

areas are armed in AWAY Mode or STAY Mode 1.

0,2 System Disarmed

This output operates when the system is disarmed.

The output is reset when the system is armed. If the

system is partitioned, this output operates when both

areas are disarmed.

0,3 Armed in STAY Mode

This output operates when the system is armed in

STAY Mode 1 or STAY Mode 2. The output is reset

when the system is disarmed. If the system is

partitioned, this output operates when either area is

armed in STAY Mode 1.

0,4 Armed in AWAY Mode

This output operates when the system is armed in

AWAY Mode. The output is reset when the system is

disarmed. If the system is partitioned, this output

operates when either area is armed in AWAY Mode.

0,5 Auto Arm Pre-Arming Alert Time

This output operates during the time period before

the control panel is automatically armed in AWAY

Mode or STAY Mode 1. The output is reset when

the control panel is automatically armed in AWAY

Mode or STAY Mode 1. The Auto Arming Pre-Alert

Time is programmed in Location 481 (refer to Section

17.11 for more information).

0,6 Exit Warning with All Zones Sealed or

Entry Warning

This output operates during Exit Time when the

control panel is armed and all zones are sealed. The

output is reset when Exit Time expires.

This output operates again during Entry Time and is

reset when Entry Time expires or the system is

disarmed.

This output also operates if a zone is activated when

the system is armed in STAY Mode 1 or STAY

Mode 2 and the Entry Guard Timer for STAY Mode

is programmed in Locations 472 and 473 (refer to

Section 17.5 on page 78).

0,7 Exit Warning

This output operates during Exit Time when the

system is armed. The output is reset when Exit Time

expires.

0,8 Exit Warning Finished

This output operates after Exit Time expires when

the system is armed. The output is reset when the

system is disarmed.

0,9 Kiss-Off after Exit Time

This output operates after the first successful

transmission to the base station receiver when Exit

Time expires. The output is reset when the system is

disarmed.

0,11 Entry Warning

This output operates when during Entry Timer 1,

Entry Timer 2, or Entry Guard Timer for STAY

Mode. The output is reset when the Entry Time

expires.

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 117 118

Commentaires sur ces manuels

Pas de commentaire

Bosch ICP-CC488 Guide d'installation Page 71

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch ICP-CC488