Bosch WM 19 Spécifications

9350-7621-000 Rev G 04/2009Model WM1000/WM2000Wall Mount Intercom StationsUser Instructions93507621000 WM10002000UserManual.book Page i Monday, Apri

6InstallationConfiguration Switch Pre-checkBefore making connections, read the configuration switch notes that follow and make sure all switches are p

7Headset Microphone Type Selection (DIP Switch 4)If the headset specifications indicate the microphone type is balanced, or if you are unsure, leave t

8Intercom Channel ConnectionsIMPORTANT: The following paragraphs and illustrations describe installation of the WM1000/2000 in and Audiocom Intercom S

9issue, the operating range is now limited only by the audio transmission range, which is several miles. Another advantage to this method is more stat

10Power UpMake sure any local power supplies are plugged in, and turn ON the power switches of any phantom power supplies.NOTE: If you are using a lar

11.Figure 2 shows a 2-channel intercom system using a PS2001L Power Supply set to isolate mode. In isolate mode, each intercom channel is a separate p

12Figure 3 shows a single-channel intercom system using one PS2001L with WM1000 Intercom Stations. The PS2001L may be set to either combine or isolate

13Each PS2001L is set to combine mode and it supplies power to one intercom channel only. Each intercom channel is a separate party line, and total cu

14An example of an intercom system using all local powered stations, with no power being distributed on the intercom channels (dry lines). WM2000 stat

15FIGURE 6. Audiocom mode connections for WM1000 Intercom Station.93507621000 WM10002000UserManual.book Page 15 Monday, April 27, 2009 3:09 PM

Proprietary NoticeThe product information and design disclosed herein were originative by and are the property of Bosch Security Systems, Inc. Bosch r

16FIGURE 7. Audiocom mode connections for a WM2000 Intercom StationFIGURE 8. Audiocom mode line termination for dry line operation (one required for e

17OperationChannel Select (WM2000 Only)To change the WM2000 channel, do the following: > Tap the Ch Select key to select channel 1 or 2. The key is

Unbalanced ModeTo use the WM1000/2000 in a Clear-Com Intercom System, do the following1. Set SW1 to the UNBAL position.2. Set DIP switch 2 to the Clos

19SpecificationsGeneralPower RequirementsPhantom Power: 24VDC nominal (30VDC), 150mALocal Power: 15VDC, 150mADimensions:Mounts in a standard 2-gang el

93507621000 WM10002000UserManual.book Page 20 Monday, April 27, 2009 3:09 PM

TableOfContentsWM1000/WM2000 ...1Introduction ...

93507621000 WM10002000UserManual.book Page 2 Monday, April 27, 2009 3:09 PM

1CHAPTER 1WM1000/WM2000IntroductionThank you for purchasing the Audiocom WM1000/2000 Wall Mount Intercom Station. We hope the many design features of

2Reference ViewFIGURE 1. Reference View, WM-2000 shown.93507621000 WM10002000UserManual.book Page 2 Monday, April 27, 2009 3:09 PM

3FeaturesNOTE: The numbered features list in Channel Select Switch (WM-2000 Only) -The channel select switch is used to switch between intercom channe

4Intercom Talk Key: The talk key can be used in both momentary PTT (push-to-talk) and latching (hands-free talk) mode.Momentary Mode - Press and hold

5Call Beep - An optional call beep tone can be used for incoming call notification.Headset Mic Selection - Balanced or unbalanced microphone may be se