Bosch ICP-EZM2 Easy Series Manuel d'utilisateur télécharger pdf (Page 2)

Functions

Advanced False Alarm Reduction

The Easy Series system guards against user-generated

false alarms through design features such as

Graduated Annunciation and Intelligent Threat

Assessment. Easy Series uses enhanced false alarm

verification methods that exceed industry false alarm

reduction standards.

Graduated Annunciation

The system gradually increases the control center

volume, changes the animation of the control center

display, and incrementally pulses the warning devices.

The control center notifies users when the system is

preparing to send an alarm and provides options to

cancel reports, reducing false alarms.

Alarm Verification

The following alarm verification methods reduce false

alarms without compromising usability or reliability.

• Two-way Audio Verification: Provides remote

customers the ability to listen to and speak with

users at the protected premises.

• Sequential Verification: When two or more input

sensors activate within a specified time period, an

intrusion alarm is considered verified. For example, if

a door sensor and a motion detector both sense

alarms, the system sends a verified alarm report.

• Intelligent Threat Assessment: The Easy Series uses

protection levels, input types, input conditions, and

system event timing to assess a potential threat. If

the threat reaches a specific threshold, the system

sends a verified alarm report.

Easy Series Intrusion Control Panel Configuration

Users can configure the Easy Series with the necessary

regional parameters for a specific country without

changing hardware. Installers can configure the system

using their language of choice and then set the system

to the appropriate language for the user. Installers can

remotely program the system using a telephone or

Remote Programming Software (RPS). A voice

prompted installer mode reduces service and

installation costs while ensuring accurate

programming.

Remote Programming Software (RPS)

RPS is a separate software package that allows

computers equipped with the Microsoft Windows

operating system and a modem to act as a remote

programming, record storage, remote control, and

troubleshooting tool for specific control panels.

Certifications and approvals

Region Certification

Europe CE ICP-EZM2-EU, ICP-EZM2-LC

Technical specifications

Enclosure

Dimensions (H x W x

D):

37 cm x 31.8 cm x 8.5 cm (14.5 in x 12.5 in x

3.25 in)

Construction

Material:

Cold-rolled steel, zinc seal, 0.36 mm thick

(20 Ga.)

Environmental Considerations

Relative Humidity: 93% at 32°C 2°C (89.6°F 35.6°F)

Operating

Temperature:

-10°C to +49°C (14°F to +120°F)

CE: -10°C to +40°C (+14°F to +104°F)

NF A2P: -10°C +55°C (+14°F to +131°F)

Storage Temperature: -10°C to +55°C (+14°F to +131°F)

Protection Level IP 30 - IK 04

Supervised Points

On-board Hardwire: 8

Single or dual end-of-line (2.2 k EOL) tamper

point support

Point 1 supports two-wire smoke detectors

All points support four-wire smoke detectors

Enclosure tamper input (does not reduce

point capacity)

Reaction time lower than 250ms

Programmable Outputs (PO)

On-board: 4

PO 1 only: Configurable relay

PO 2 to PO 4: Configurable solid state

PO 4 only: Internal supervised speaker driver

option

PO 1 Relay Rating: Contacts: 2 A with no jumper installed;

resistive loads only; in a NF A2P certified

installation: 1 A

Output: 1.2 A with jumper installed; resistive

loads only; in a NF A2P certified installation 1

Operating Voltage: 30 VDC maximum

PO 2 to PO 4 Rating: 400 mA current sink

Number of...

Users: 22

User 1: Master user

Users 2 to 21: System users

User 22: Duress user

Events: 500 history events, stamped with time and

date

Tokens and Key Fobs: One per user (User 22 does not receive a

token or key fob)

Phone Line

Phone line trouble

voltage

Trouble condition occurs when the phone line

voltage is between 1.10 V and 4.75 V

Control Panel Power Requirements

2 | Easy Series

1 2 3 4

Easy Series 1
4 4

Commentaires sur ces manuels

Pas de commentaire

Bosch ICP-EZM2 Easy Series Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Composants des dispositifs de sécurité Bosch ICP-EZM2 Easy Series