Bosch LTC 2604 Manuel d'instructions télécharger pdf (Page 10)

IntuiKey Series | Instruction Manual | Mounting the IntuiKey

Bosch Security Systems | 28 June 2004

System power connections must also be considered.

Depending on the distance between the keyboard and

devices under control, an external power supply may be

needed according to the following specifications:

*NOTE: Distances may vary depending on the number

of keyboards connected.

2.2 Mounting the IntuiKey

The IntuiKey LCD displays are readable in all but

direct sunlight conditions. Locate the keyboard on a

flat horizontal surface, with an optimal LCD viewing

angle of 0 to 20 degrees from vertical. Display contrast

levels are software-controlled and may be adjusted

via the Keyboard Control Menu (as described in

SECTION 3.4). An optional rack mount kit may

also be used.

2.3 Connecting to the IntuiKey

1. Refer to FIGURE 2-2 for details on the

input/output connections supplied by the IntuiKey

Keyboard. Four connectors are located on the

IntuiKey rear panel: (2) RJ-11 connectors,

(1) female 9-pin sub-D connector, and a DC power

jack. The RJ-11 connectors are labeled as Allegiant

and MUX/DVR, and the 9-pin sub-D is labeled

RS-232 Serial Port.

FIGURE 2-2 Back Panel Connections of IntuiKey

ATTENTION: To ensure proper system functioning

and to prevent damage to the unit, it is critical that

only Allegiant devices be connected to the Allegiant

connector, and Multiplexer/DVR devices be

connected to the MUX/DVR connector.

2. If desired, the data/power cables can be looped

through either of the two tabs found at the bottom

of the rear panel to increase strain relief

capabilities.

3. Review the configuration options shown in

FIGURE2-4. Make the necessary keyboard data

and power connections that are best suited to your

system requirements based on these diagrams.

When connecting to Divar DVRs or System4

Multiplexers, attach the supplied 390 Ohm

terminator to the Out connector on the last device.

NOTE: In systems having multiple Divar DVRs or

multiple System4 Multiplexers, use the front panel

controls on the video devices to assign appropriate

address numbers and starting camera numbers. The

IntuiKey will not properly recognize the video devices

if there are conflicting addresses in the system.

4. After power is applied, the keyboard initializes and

displays the following:

FIGURE 2-3 Initial Power-up Display

5. After a brief pause (or immediately after the CLR

button is pressed), the keyboard will perform a

brief search for connected devices.

NOTE: On initial power-up, factory reset, or firmware

upgrade, the IntuiKey displays a Language Menu. Select

the desired language by pressing the softkey next to

the language title. If additional languages are available,

the arrow softkeys at the bottom of the screen can be

used to scroll to a second menu screen.

MUX / DVR ALLEGIANT 12 VDC RS-232 SE RIAL PORT

MUX/DVR

DC Power

Allegiant

RS-232

Serial Port

Cable Strain Reliefs

KBD – Universal

Bosch Security System

Press [CLR] key to

Exit

Prod Mon

Clr

321

654

987

Shot

KBD – Universal

Bosch Security System

Firmware Ver: x:xx

Protocol: .6P

Firmware Ver: x:xx

Bootldr Ver: x:xx

Hardware Ver: x:xx

Distance from Keyboard Optional Equipment

to Device under Control* Needed

Less than 10 ft (3.5 m) NONE

Between 10 ft (3.5 m) KBD-120PS/KBD-220PS

and 100 ft (30 m) External Power Supply

Greater than 100 ft (30 m) LTC 8557/60(50)

Keyboard Extender

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Bosch LTC 2604 Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch LTC 2604