Bosch ICP-CC488 Spécifications télécharger pdf (Page 10)

ICP-CC488 | Quick Reference Guide | 1.0 Overview EN | 10

Bosch Security Systems, Inc. | 12/08 | F01U089458-02

1.20 Fault Analysis

1. Press and hold the [5] key until two beeps are

heard.

2. Zone Indicators display FAULT conditions (refer

to Table 7).

3. Press [#] key to exit.

Table 7: Fault Analysis Conditions

Zon

LED

Fault Condition Description

1 System Fault

Press and hold button [1] to

determine fault.

1 – Battery Fail

2 – Date/Time

3 – RF Rx Jamming

RF Rx Tamper

RF Rx Comm’s Fail

4 – Horn Speaker Fail

5 – Telephone Line Fail

6 – EEPROM Fail

7 – AUX Power Supply Fail

8 – AC Fail

2 RF Low Battery Press and hold button [2] to

determine fault.

Displays zones (1 to 8) that

3 Zone Tamper Press and hold button [3] to

determine fault.

Displays zones (1 to 8) that

4 Sensor Watch Press and hold button [4] to

determine fault.

Displays zones (1 to 8) that

5 RF Sensor

Watch

Press and hold button [5] to

determine fault.

Displays zones (1 to 8) that

6 Communication

Fail

Press and hold button [6] to

determine fault.

1 – Receiver 1 Fail (Dialer)

2 – Receiver 2 Fail (Dialer)

1.21 Modem Call (Alarm Link)

Press and hold the [6] key until two beeps are heard.

1.22 Latching Outputs (Reset)

Press and hold the [7] key until two beeps are heard.

1.23 Codepad ID/Buzzer Tone

1. Press and hold the [8] key until the desired

buzzer tone is reached.

If the system is partitioned (CC488 only), the

codepad displays a number identifying which

area the codepad belongs (refer to Table 8).

2. Press the [#] key to exit.

Table 8: Codepad ID/Buzzer Tone

Zone LED Codepad Assignment

1 Area 1

2 Area 2

7 Master Partitioned Codepad

1.24 Test Report

Press and hold the [9] key until two beeps are heard.

1.25 Speaker Test

Press and hold the [1] key until two beeps are heard.

The speaker sounds for two sec.

1.26 Bell Test

Press and hold the [2] key until two beeps are heard.

The piezo sounds for two sec.

1.27 Strobe Test (Toggle On/Off)

Press and hold the [3] key until three beeps are heard

to turn the strobe on.

Press and hold the [3] key until two beeps are heard

to turn the strobe off.

1.28 Telco Arm Sequence (Call Forward

On)

1. Enter your four character Installer Code or

Master Code followed by [3] and the [#] key (for

example, [1 2 3 4 3 #]).

2. Press [1] followed by the [#] key.

3. Enter the Call Forward On sequence.

4. Press the [#] key to exit.

1.29 Telco Disarm Sequence (Call

Forward Off)

1. Enter your four character Installer Code or

Master Code followed by [3] and the [#] key (for

example, [1 2 3 4 3 #]).

2. Press [2] followed by the [#] key.

3. Enter the Call Forward Off sequence.

4. Press the [#] key to exit.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Bosch ICP-CC488 Spécifications Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch ICP-CC488