Bosch ICP-CC404 Guide de l'utilisateur Page 14
- Page / 24
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ICP-CC404 | User's Guide | 20.0 Domestic Dialing
14 Bosch Security Systems, Inc. | 12/08 | F01U089400-02
3. Hang up the telephone.
The system remains armed.
If your installer programmed answering
machine bypass, you must call the control
panel twice to connect to the system. For
example, call the telephone number for
the control panel, let the call ring no more
than four times, and then hang up the
telephone. Wait at least 8 sec and call the
control panel again.
20.0 Domestic Dialing
Domestic dialing enables the control panel to call
your mobile phone or a relative or friend if the
system detects an alarm. You can program up to
three different telephone numbers to call when an
alarm occurs. Although only your installer can set
the system to report in the domestic format, the
Master Code holder can change the domestic
telephone numbers at any time.
20.1 Acknowledging Domestic Calls
If an alarm occurs, the system calls the first
programmed telephone number. When you answer
an incoming call, the system sounds a repeating siren
tone followed by a pause, continuously for 2 min (for
example, siren tone, pause, siren tone, and pause).
If you do not acknowledge the call from the control
panel during a pause between siren tones, the control
panel hangs up after 2 min, and calls the next
telephone number.
Press [*] for 1 to 3 sec during the pause to
acknowledge the call.
If you acknowledge the call, the control panel does
not call any more phone numbers for that event. If
the call is successfully acknowledged, a tone of
decreasing pitch sounds.
Table 11: Domestic Dialing Telephone Digits
Digit
Required
Number to
Program
Digit
Required
Number to
Program
0 0 8 8
1 1 9 9
2 2
3 3 * *1
4 4 # *2
5 5 4-sec pause *3
6 6 break *4
7 7
20.2 Programming Domestic Telephone
Numbers
If your system is configured for domestic dialing, the
Master Code holder can program the telephone
numbers the control panel calls if an alarm occurs.
To program telephone numbers:
1. Enter your four-character Master Code and press
[2 #] (for example, [2 5 8 0 2 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
If there are telephone numbers already
programmed, the numbers appear one digit at a
time by the codepad indicators.
If there are no telephone numbers programmed,
another two beeps sound after entering this
mode. These two beeps are normally heard after
the last digit of the last telephone number
appears.
2. Enter the first telephone number (for example,
[9 6 7 2 1 7 1 7]).
As you enter each digit, the corresponding
codepad indicators light.
3. To program another telephone number, press
[* 4] and repeat Step 2.
This inserts a break between the first telephone
number and the second telephone number.
4. Press [#] to exit from this function.
20.3 Disable Domestic Dialing
To suspend domestic dialing (for example, you are
moving and do not want the system to continue
calling your mobile phone):
1. Enter your four-character Master Code and press
[2 #] (for example, [2 5 8 0 2 #]).
Two beeps sound and the STAY and AWAY
indicators flash.
2. Press [* 4 #].
The STAY and AWAY indicators turn off.
21.0 Basic Pager Reporting
This feature only applies if your system reports to a
pocket pager. Basic pager reporting requires some
interpretation of the numbers that appear on the
display. It is possible to differentiate between 1000
different systems when a number of control panels
report to the one pocket pager.
Subscriber ID Number
This is the identification number of the control panel.
Only your installer can program this number.
Zone Status
The zone status display shows the status of each zone
(1 to 8). Table 12 describes each number of the zone
status display.
- ICP-CC404 1
- Copyright Notice 2
- Notice of Liability 2
- New Zealand Telepermit Notes 2
- Contents 3
- 1.0 Introduction 4
- 2.0 Features 4
- 3.0 Codepad Indicators 5
- 4.0 Arming the System 6
- 4.1 Arming in AWAY Mode 7
- 4.2 Arming in STAY Mode 1 7
- 4.3 Arming in STAY Mode 2 7
- 5.0 Disarming the System 8
- 6.0 User Codes 8
- 7.0 Radio Transmitter 9
- Operations 9
- 8.0 Alarms 9
- 9.0 Isolating Zones 10
- 11.0 Fault Analysis Mode 11
- 12.0 Telco Arm/Disarm 11
- Sequence (Call Forward 11
- On/Off) 11
- 13.0 Turning Outputs On/Off 12
- 14.0 Reset Latching Outputs 12
- 15.0 Codepad ID/Buzzer Tone 12
- 16.0 Testing 13
- 17.0 Event Memory Recall 13
- 18.0 Day Alarm 13
- 19.0 Remote Arming By 13
- Telephone 13
- 20.0 Domestic Dialing 14
- 21.0 Basic Pager Reporting 14
- 22.0 Glossary of Terms 17
- 23.0 Installation Notes 19
- Zone Description 20
- User Code Names 20
- 24.0 Specifications 22
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch ICP-CC404
(40 pages)
(4 pages)
(8 pages)Philips CD6551B22 manuali
Manuali dei proprietari e guide per l'utente per Lettori DVD Philips CD6551B22.
We fornisce manuali pdf Philips CD6551B22 per scaricare gratuitamente in base al tipo di documento:
Commentaires sur ces manuels