Bosch ICP-CC404 Guide d'installation Page 22
- Page / 98
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ICP-CC404 | Installation Guide | 4.0 System Operations
22 Bosch Security Systems, Inc. | 12/08 | F01U089401-02
2. Enter the number of the zone to isolate and press
[STAY].
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
as you press [STAY]. All other Burglary Zones
are automatically isolated only after the system is
armed.
3. Repeat Step 2 for each zone you want to isolate.
As each zone is selected to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the selected zones continue to
flash until the next time the system is disarmed.
Example
To manually isolate zones 1, 3, and 4, press:
[STAY][STAY][1][STAY][3][STAY][4][STAY]
[AWAY]
4.11.2 Code to Isolate
The code to isolate method permits only those User
Code holders with a priority level that includes Code
to Isolate. The standard isolating method is disabled
for any User Code with this priority level.
1. Press [STAY].
2. Enter your code and press [STAY].
Three beeps sound and the STAY indicator
flashes.
If you attempt to enter Isolating Mode with a
User Code that is not set for Code to Isolate, the
system ignores the attempt.
3. Enter the number of the zone to isolate and press
[STAY].
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
you press [STAY]. All other burglary zones are
automatically isolated only after the system is
armed.
4. Repeat Step 3 for each zone to isolate.
As each zone is selected to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
5. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the selected zones continue to
flash until the next time the system is disarmed.
Example
To manually isolate zones 1, 3, and 4, press:
[STAY][User Code][STAY][1][STAY][3][STAY][4]
[STAY][AWAY]
4.12 Fault Analysis Mode
Whenever a system fault occurs, the FAULT or
MAINS indicator flashes and the codepad beeps once
per minute.
If the MAINS indicator flashes, the AC MAINS
supply is disconnected from the control panel. Refer
to AC MAINS Failure on page 24.
To enter Fault Analysis Mode to determine a system
fault other than the AC MAINS supply:
1. Press and hold [5] until two beeps sound.
The FAULT indicator remains lit and the STAY
and AWAY indicators flash.
The lit zone indicators indicate the type of fault
that occurred. Refer to Table 14.
2. To exit from the Fault Analysis Mode, press
[AWAY].
The STAY and AWAY indicators turn off and
the FAULT indicator remains lit.
Table 14: Fault Indicators
Indicator Fault Description
1 Low battery
2 Date and time
3 Sensor watch
4 Horn speaker disconnected
5 Telephone line fault
6 EEPROM fail
7 AUX Power Supply fail
8 Communications failure
4.13 Fault Descriptions
1 – Low Battery
A low battery fault occurs when the battery supply
voltage falls below 11.2 VDC or when a Dynamic
Battery Test detects a low capacity battery. This fault
clears after a successful Dynamic Battery Test. The
system performs a Dynamic Battery Test every 4
hours after power is connected to the control panel
and every time the system is armed.
When reporting to the base station receiver, the
control panel sends a Battery Test Failure Report
(Contact ID Event Code 309) to indicate the low
battery fault.
- ICP-CC404 1
- Copyright Notice 2
- Notice of Liability 2
- Contents 3
- 1.0 Introduction 7
- 2.0 Programming 9
- 2.2 Programming with the 10
- Programming Key 10
- 2.3 Programming Option Bits 10
- 3.0 Codepad Indicators 16
- Codepad 17
- 4.0 System Operations 18
- 4.7 Codepad Duress Alarm 21
- 4.8 Codepad Panic Alarm 21
- 4.9 Codepad Fire Alarm 21
- 4.10 Codepad Medical Alarm 21
- 4.11 Isolating Zones 21
- 4.12 Fault Analysis Mode 22
- 4.13 Fault Descriptions 22
- AUX Power Supply Fail 23
- Operations 24
- Held Transmitter Operations 25
- 6.0 System Functions 27
- 6.2 Master Code Functions 31
- 6.3 Hold-Down Functions 37
- 7.0 Remote Arming by 38
- Telephone 38
- 8.0 Alarm Link Software 39
- 9.0 Domestic Dialing 40
- Domestic Reporting 41
- 10.1 Transmission Formats 42
- 11.0 Dialer Information 46
- 11.6 Dialing Format 48
- 11.7 Telco Arming Sequence 48
- 11.10 Ring Count 49
- 12.0 Dialer Options 50
- 13.0 Access Code 51
- 13.3 User Code Priority 52
- 14.0 Zone Information 53
- 14.3 Zone Programming 54
- 15.0 System Reporting 60
- Information 60
- Restore Report 63
- 15.21 Test Reporting Time 63
- 16.0 Programmable Outputs 64
- 16.2 Output Event Types 65
- 16.3 Output Polarity 68
- 17.0 System Event Timers 70
- 18.0 System and Consumer 73
- Options 73
- 18.3 System Options 3 74
- 18.4 System Options 4 74
- 18.5 Consumer Options 1 75
- 18.6 Consumer Options 2 75
- 18.7 Consumer Options 3 75
- 19.0 Optional Equipment 76
- (CP508LW) 77
- 20.1 Terminal Descriptions 78
- 20.2 Glossary Of Terms 79
- 20.3 Diagrams 81
- 1 2 3 4 5 83
- 21.0 Specifications 84
- 22.0 Programming Sheets 85
- 22.1 Country Codes 93
- Bosch Security Systems, Inc 98
- 130 Perinton Parkway 98
- Fairport, NY 14450-9199 USA 98
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch ICP-CC404
(28 pages)
(12 pages)Philips CD6551B22 manuali
Manuali dei proprietari e guide per l'utente per Lettori DVD Philips CD6551B22.
We fornisce manuali pdf Philips CD6551B22 per scaricare gratuitamente in base al tipo di documento:
Commentaires sur ces manuels