Bosch FW5.50 Manuel d'utilisateur télécharger pdf (Page 68)

68 en | Setting up VCA Camera Browser Interface

AM18-Q0611 | v5.50 | 2012.03 Software manual Bosch Security Systems

12 Setting up VCA

Several VCA configurations are available.

– Off

– Silent MOTION+

– Profile #1

– Profile #2

– Scheduled

– Event triggered

12.1 VCA - Silent MOTION+

The Silent MOTION+ configuration is active by default. In this

configuration, metadata is created to facilitate searches of

recordings, however, no alarm is triggered.

 In the VCA configuration drop-down list, select Silent

MOTION+.

No parameters can be changed for this selection.

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 93 94

Camera Browser Interface 1
Table of Contents 3
1 Browser connection 10
1.3 Protected network 11
2 System Overview 12
3 Operation via the browser 13
3.1.2 Status icons 14
3.1.5 System Log / Event Log 16
3.1.6 Saving snapshots 17
3.1.10 Processor load 18
3.1.9 Audio communication 18
3.2 Recordings page 19
3.2.1 Controlling playback 20
4 Settings Overview 22
4.2 Settings 23
5Basic Mode 24
5.2 Date/Time 25
5.3 Network 26
5.4 Encoder 27
5.5 Audio 27
5.6 Recording 27
5.7 System Overview 27
6 Advanced General Settings 28
6.2 Password 29
6.3 Date/Time 30
6.3.5 Time server IP address 31
6.3.6 Time server type 31
6.4 Display Stamping 32
6.4.5 Alarm message 33
6.4.6 Video watermarking 33
7 Web Interface 34
7.2 LIVEPAGE Functions 35
7.2.7 Show system log 36
7.2.8 Allow snapshots 36
7.2.9 Allow local recording 36
7.2.10 I-Frame only stream 36
7.3 Logging 37
8 Camera 38
8.2 Picture Settings 39
8.2.2 Day/Night 40
8.3 Encoder Settings 41
8.4 Audio 42
8.5 Pixel Counter 42
9 Encoder Settings 43
9.1 Encoder Profile 44
9.1.3 Profile name 45
9.1.4 Target bit rate 45
9.1.5 Maximum bit rate 45
9.1.6 Encoding interval 45
9.1.8 Expert Settings 46
9.1.9 Default 47
9.2 Encoder Streams 48
9.2.2 JPEG stream 49
10 Recording 50
10.1 Storage Management 51
10.2 Recording Profiles 54
10.2.2 Standard recording 55
10.2.3 Alarm recording 55
10.3 Retention Time 57
10.4 Recording Scheduler 58
10.4.3 Profile names 59
10.4.4 Activate recording 59
10.4.5 Recording status 59
10.5 Recording Status 60
11 Alarm 61
11.1.5 Video transmission 62
11.1.6 Stream 62
11.1.7 Remote port 62
11.1.8 Video output 62
11.1.9 Decoder 62
11.1.10 SSL encryption 63
11.1.11 Auto-connect 63
11.1.12 Audio 63
11.3 Audio Alarm 65
11.4 Alarm E-Mail 66
11.4.8 Destination address 67
11.4.9 Sender name 67
11.4.10 Test e-mail 67
12 Setting up VCA 68
12.2 VCA - Profiles 69
12.2.2 Analysis type 70
12.2.3 Motion detector 70
12.2.4 Tamper detection 71
12.3 VCA - Scheduled 75
12.4 VCA - Event triggered 77
13 Interfaces 78
14 Network 79
14.1.3 IP V6 address 80
14.1.4 DNS server address 80
14.1.5 Video transmission 80
14.1.6 HTTP browser port 80
14.1.7 HTTPS browser port 80
14.1.8 RCP+ port 1756 81
14.1.9 Telnet support 81
14.1.10 Interface mode ETH 81
14.1.11 Network MSS [Byte] 81
14.1.12 iSCSI MSS [Byte] 81
14.1.19 Status 83
14.2 Advanced 84
14.2.5 RTSP port 85
14.2.6 UPnP 85
14.2.7 TCP metadata input 85
14.2.8 Quality of Service 85
14.3 Multicast 86
14.3.3 Port 87
14.3.4 Streaming 87
14.3.5 Multicast packet TTL 87
14.4 FTP Posting 88
14.5 IP V4 filter 89
15 Service 90
15.1.2 Configuration 91
15.1.3 SSL certificate 91
15.2 System Overview 92
Bosch Security Systems 94

Commentaires sur ces manuels

Pas de commentaire

Bosch FW5.50 Manuel d'utilisateur Page 68

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Bosch FW5.50