Bosch D1255RB Guide d'installation télécharger pdf (Page 45)

D9412GV2/D7412GV2 | Operation and Installation Guide | 9.0 Off-Board Points

Bosch Security Systems, Inc. | 7/09 | F01U003641-04 45

Figure 19: Program Record Sheet

EN | 25

bold

Point Assignments (001 through 040)

POPIT Switch

Setting

Trans-

lation

Point

Index

Area

Assign

Debounce

BFSK/

Relay

Custom Point Text

100 001 (3) _ _ (1) ___ (2) _____ (1) ____

P1 FIRE

___________________

200 002 (1) _ _ (1) ___ (2) _____ (2) ____ P2 PANIC ___________________

300 003 (25) _ _ (1) ___ (2) _____ (3) ____ P3 DELAY ___________________

400 004 (13) _ _ (1) ___ (2) _____ (4) ____ P4 FOLLOW ___________________

500 005 (7) _ _ (1) ___ (2) _____ (5) ____ P5 INSTANT ___________________

600 006 (7) _ _ (1) ___ (2) _____ (6) ____ P6 INSTANT ___________________

700 007 (7) _ _ (1) ___ (2) _____ (7) ____ P7 INSTANT ___________________

800 008 (7) _ _ (1) ___ (2) _____ (8) ____ P8 INSTANT ___________________

0 1 2 3 4 5 6 101 009 __ __ (1) ___ (2) _____ (1) ____ P9 ___________________

Default values are shown in ( ) or in bold

D9412GV2/D7412GV2 | Program Record Sheet | RADXPNTS Handler

9.3.8 POPIT Labels

D9412GV2 off-board points are numbered 9 to 127

and 129 to 247. The D7412GV2 uses Points 9 to 75

only. The D9412GV2 reserves Points 128 and 248 for

internal use. POPITs must be connected for Points

129 to 247 to expansion loops connected to POPEX

#2.

Two sheets of peel-off POPIT labels are supplied with

the D8125 POPEX Module. Use the sheet marked

“Bank1” for Points 9 to 127. Use the sheet marked

“Bank2” for Points 129 to 247.

Each label has two parts. Place the smaller part (with

only the point number) on the chip. Place the larger

part with the switch settings on the base of the

POPIT. Set the switches and cover the POPIT.

Do not program two POPITs for the same point

number. After programming all the points, perform a

Service Walk Test. Refer to Section 4.10 Service

Walk Test on page 47. If a point does not test, check

the programming for a duplicated address.

Walk Test and Service Walk Test Do Not Show

Extra Points: If the point assignment switches on a

POPIT or OctoPOPIT are set incorrectly, missing and

extra points can occur. If the same point number is

assigned to two or more POPITs or OctoPOPITs,

none of the points with that number test correctly.

Refer to Section 9.1 Point (Zonex) Bus: D9412GV2

Terminals and D7412GV2 Terminals on page 39.

For UL 864 Commercial Fire applications,

refer to Installing Combination Fire and

Intrusion Alarm Systems in the

D9412GV2/D7412GV2 Approved

Applications Compliance Guide

(P/N: F01U003639) for important

information about combination fire and

intrusion systems.

9.4 D8128D OctoPOPIT Module

Modules D8128, D8128A, or D8128B are

incompatible with the D9412GV2 or

D7412GV2. Use only the D8128D

OctoPOPIT Module. Using Modules

D8128, D8128A, or D8128B can cause

intermittent Missing and Restoral Reports.

9.4.1 Description

The D8128D OctoPOPIT Module combines the

functions of the D8125 POPEX Module and the

D8127/D9127 POPIT Modules to provide eight off-

board points in a single module. You can wire both

D8128D OctoPOPIT and D8125 POPEX Modules in

parallel to the Zonex Bus terminals on the same

control panel.

Review Section 6.0 Power Outputs on page 28 to

ensure that there is enough power for the

OctoPOPITs and other powered devices that will be

connected to the system.

Up to thirty D8128D Modules can be connected to the

D9412GV2 Control Panel. Up to nine D8128Ds can

be connected to the D7412GV2 Control Panel (three

points can be used on the last OctoPOPIT).

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 103 104

Commentaires sur ces manuels

Pas de commentaire

Bosch D1255RB Guide d'installation Page 45

Commentaires sur ces manuels

Produits connexes et manuels pour Claviers numériques Bosch D1255RB