Bosch D9000, G Manuel d'utilisateur télécharger pdf

ELAN Home Systems ● 1690 Corporate Circle ● Petaluma, CA 94954 USA

tech support: 800.622.3526 • main: 760.710.0990 • sales: 877.289.3526 • email: [email protected]

Integration Note

Manufacturer: Bosch / Radionics

Model Number(s): D7000, D9000 Series Panels, D7000/9000V2 Panels

Core Module Version:

Comments: Tested Firmware Revisions: 6.80, 7.07

Document Revision Date: 1/30/2013

OVERVIEW AND SUPPORTED FEATURES

The Bosch / Radionics D9000/D7000 Series security panels integrate with the g! system using an RS-

232 serial connection. The panel requires the DX4010I Serial Interface Module to enable the RS-232

communication between the g! system controller and the control panel.

Integration of the security system provides monitoring and control from any touch screen, telephone or

computer both locally and remotely. Additionally, events occurring in the security system can trigger

system commands in other sub-systems in the home. For example, a burglar alarm can turn all the lights

on and send out email alerts. The security system can also receive commands as a result of events

within other sub-systems. For example, changing the house mode from Home to Vacation can trigger a

security command to arm the system.

IMPORTANT! For systems with more than one partition (“area”), you must program keypads in a

specific manner to be able to arm and disarm all partitions from the g! interface. See Panel

Programming, and the section on Keypad Setup, for more information

THE BOSCH PANELS SUPPORT THE FOLLOWING FEATURES:

Arm – Disarm: Arm and disarm from the Viewer interface is supported for any partition. Status

information is available for all partitions.

Auto Arm: Arming as a System Command from the Event Mapper is supported for any partition. By

default, automatic arming is disabled in the Configurator.

Zone Status: Zone status information for all zones is properly shown in the Viewer.

History View: The history view is supported on any Viewer.

Bypassable Zones: If a zone is programmed as a bypassable zone in BOTH the security panel and the

Configurator, the Security Tab in the Viewer will allow you to bypass that zone. The Configurator does

not auto-detect if a zone is bypassable: you must set each zone with the Configurator to enable this

feature.

Auto Zone and Partition Detection: The g! system will automatically detect the zone number, zone

name, and partition number.

HE BOSCH PANELS DO NOT SUPPORT THE FOLLOWING FEATURES:

Any feature not specifically noted as supported should be assumed to be unsupported.

1 2 3 4 5 6

Résumé du contenu

Page 1 - Integration Note

ELAN Home Systems ● 1690 Corporate Circle ● Petaluma, CA 94954 USA tech support: 800.622.3526 • main: 760.710.0990 • sales: 877.289.3526 • email: elan

Page 2 - CONNECTION DIAGRAM

2 of 6 INSTALLATION OVERVIEW 1. Install the security system and program the panel for the RS-232 interface. 2. Install the DX4010I and set the dip

Page 3 - PANEL PROGRAMMING

3 of 6 DIAGRAM 1: SECURITY PANEL TO DX4010I SERIAL INTERFACE MODULE WIRING DIAGRAM The following diagram shows how to wire the DX4010I to the panel.

Page 4 - RMING PIN CODES AND AUTO-ARM

4 of 6 ARMING PIN CODES AND AUTO-ARM Because Auto-Arming is a global setting in the g! system, All Bosch panels must have the same settings for the Au

Page 5 - CONFIGURATION DETAILS

5 of 6 g! CONFIGURATION DETAILS The following table provides settings used in the g! Configurator. Please refer to the Configurator Reference Guide f

Page 6 - COMMON MISTAKES

6 of 6 COMMON MISTAKES 1. Using the incorrect Elan DB-9 to RJ-45 adapter to connect to the security panel hardware. Use the HA-CB-328, which provides