Bosch SM024 Spécifications Page 6
- Page / 96
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6 | Configurability SM Series Heat Pump
SM Series Heat Pump6 720 220 406 (2013/1) Subject to change without prior notice
CONFIGURABILITY
HORIZONTAL CONFIGURABILITY
The Horizontal Configuration water source heat
pump is designed to have a field configurable
blower orientation: end blow (default) and straight
through. (Figure #4 and #5)
Figure # 4
Figure # 5
Left- Hand unit instructions refer to Pg#6 and
Right-Hand unit instructions refer to Pg#9.
Required Tools
• 5/16" hex head driver
• 3/8" hex head driver
• 7/16" hex head driver
• Flat screw driver
• Phillips screw driver
• 1/4" hex head driver
• Needle nose pliers
• 5/16”-1/4” ratchet wrench
Instructions - Left-Hand Unit (SM0**-
1HZ-*
L*-**)
1. Remove and retain end and side panels.(Figure
#6)
Figure # 6
2. Disconnect blower motor wiring and ground
wire fastened to blower housing.(Figure#7)
Figure # 7
Left-Hand and Right-hand Horizontal (HZ) units
have different Blower Configuration instructions.
Internally mounted electric heat is only available
in End Blow configuration.
Blower configuration changes should be done
prior to unit being installed in the final location.
If unit is equipped with optional Electric
Heat and Blower re-configuration is
required: Electric Heat components, blower
collar, and Electric Heat associated wiring
will need to be removed. Additionally,
overall unit wiring will need to be
reconfigured for single power connection.
Contact Bosch After Sales for guidance.
1
1
2
2
- Heat pump 1
- CONTENTS 2
- MODEL NOMENCLATURE 3
- STANDARD PACKAGE 4
- GENERAL DESCRIPTION 4
- MOVING AND STORAGE 5
- INITIAL INSPECTION 5
- LOCATION 5
- Figure # 6 6
- Figure # 7 6
- Figure # 4 6
- Figure # 5 6
- Figure # 20 9
- Figure # 21 9
- Figure # 22 9
- Figure # 23 9
- Figure # 24 9
- Figure # 25 10
- Figure # 26 10
- Figure # 27 10
- Figure # 28 10
- Figure # 29 10
- Figure # 33 11
- Figure # 34 11
- Figure # 30 11
- Figure # 31 11
- Figure # 32 11
- COUNTER-FLOW CONFIGURABILITY 12
- VERTICAL CONFIGURABILITY 12
- Figure # 39 Back Discharge 13
- Figure # 40 Side Discharge 13
- Figure # 41 13
- Required Tools 14
- Access to Internal Components 14
- Figure # 43 15
- Figure # 44 15
- Figure # 45 15
- Figure # 46 15
- Blower Re-configuration 16
- Figure # 56 18
- Figure # 57 18
- Figure # 58 18
- Figure # 59 18
- Figure # 60 18
- Ensure to retain the spring 19
- HRP Switch Relocation 20
- Electric Heat Relocation 21
- Figure # 80 23
- Figure # 81 23
- Figure # 82 23
- Figure # 83 23
- Reinstall All Panels 24
- Figure # 87 25
- Figure # 88 25
- Figure # 89 25
- Figure # 90 25
- Figure # 91 25
- RETURN AND DISCHARGE DUCT 26
- MOUNTING VERTICAL UNITS 27
- MOUNTING HORIZONTAL UNITS 27
- CONDENSATE DRAIN 27
- DUCT SYSTEM 28
- ELECTRICAL 29
- Figure # 96 30
- Figure # 97 30
- Figure # 98 31
- Figure # 99 31
- ECM INTERFACE BOARD 33
- Hot Gas Reheat (HGRH) 35
- Electric Heat 35
- Heat Recovery Package (HRP) 35
- Figure # 101 36
- Figure # 102 36
- HEAT RECOVERY PACKAGE 38
- Water Tank Preparation 38
- HR Water Piping 38
- Water Tank Refill 38
- Initial Start-Up 39
- SEQUENCE OF OPERATION 40
- Cooling Mode 40
- Heating Mode 40
- APPLICATION CONSIDERATIONS 42
- Well Water Systems 42
- Cooling Tower/Boiler Systems 42
- Geothermal Systems 43
- Figure # 107 44
- SYSTEM CHECKOUT 45
- UNIT START-UP 45
- MAINTENANCE 45
- UNIT CHECK-OUT SHEET 47
- Customer Data 47
- Unit Nameplate Data 47
- Operating Conditions 47
- Auxiliary Heat 47
- UPM Board LED Indications 48
- Unit Troubleshooting 48
- Compressor Ohms 50
- HRP Troubleshooting 51
- ELECTRONIC THERMOSTAT 52
- INSTALLATION 52
- OPERATING TEMPERATURES AND 53
- PRESSURES 53
- COOLING HEATING 54
- AIRFLOW TABLES 58
- (SM0**-***-*** 58
- Table(SM0**-***-***-T*) 59
- WIRING DIAGRAMS 60
- Figure # 114 61
- Figure # 115 62
- Figure # 116 63
- Figure # 117 64
- Figure # 118 65
- Figure # 119 66
- WIRING HARNESS DRAWINGS 67
- Figure # 121 68
- SPARE PARTS LIST 69
- Vertical (VT) 69
- VT Parts List - Cabinet 71
- VT Parts List - Blower 72
- Electrical 73
- 6 720 220 408 (02) 74
- Horizontal (HZ) 76
- HZ Part List - Cabinet 78
- HZ Parts List - Blower 79
- HZ Parts List - Refrigeration 80
- HZ Part List - Panels 81
- HZ Part List - Detailed View 82
- Counter Flow Part List 83
- 6 720 220 430 (00) 85
- DIMENSIONAL DRAWINGS 90
- Horizontal - Straight Through 91
- Figure # 139 92
- Counter Flow 93
- Vertical 94
- Revised 05-12 96
Produits connexes et manuels pour Pompes à chaleur Bosch SM024
Pompes à chaleur Bosch SM070 Spécifications
(100 pages)
(100 pages)
(84 pages)
Pompes à chaleur Bosch SM024 Spécifications
(41 pages)
(41 pages)
Pompes à chaleur Bosch SM024 Spécifications
(32 pages)
(32 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.374 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels