Bosch BOVA-36HN1-M18M Manuel d'utilisateur Page 38
- Page / 44
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
38
|
Bosch IDS BOVA Installation Instructions
12.2016 | Bosch Thermotechnology Corp.Data subject to change
16.2 For BOVA 60
FT
T5
TF
PFC-L
L1
L2
4T
HPS
EEV
Y
W
C
B
PT
SV1
CCH
U
V
W
P
V
W
U
V
W
8P
P2
ORANGE
WAIT 2 MINUTES AFTER DISCONNECTING POWER,THEN
VERIFY DC VOLTAGE LESS THAN 42 VDC AT INVERTER
COMPONENTS MAY STORE A
DANGEROUS ELECTRICAL POTENTIAL OF 380 VOLTS DC.
FAILURE TO FOLLOW THIS WARNING COULD RESULT
IN PERSONAL INJURY OR DEATH
TEST POINTS P2-P4.
USE COPPER CONDUCTORS ONLY
D
IS
P
4
COMP
CCH
4-WAY VALVE
EEV
ELECTRIC EXPANSIVE VALVE
HPS
HIGH PRESSURE SWITCH
T3
T5
T4
CONDENSER TEMPERATURE SENSOR
CRANKCASE HEATER
COMP. DISCHARGE TEMPERATURE SENSOR
SV1
PFC-L
PFC INDUCTANCE
T
P
PRESSURE TRANSDUCER
ONLY FOR HP MODEL
B AND W ONLY FOR HP MODEL
BROWN
RADIATOR TEMP. SENSOR
COMPRESSOR
RED
3
+
-
U
N
V
I
N
_
N
YE
LLOW
P9
P10
BR
OWN
+
-
N
_1
YELLOW
1
2
3
4
5
DB1
CN9
9
1
NC
ORANGE
RED
BLUE
BLUE
PFC-L
L
D
P
Compression ratio protection limit
U
The T3 sensor is not seated fault
C
Compressor current protection limit
H
Compressor oil return
C3
Forced operation mode
T3 high temperature limit
T5 high temperature limit
AtL
F
TF high temperature limit
Voltage protection limit
C
N6
CN1
Ambient Temperature Limited
GREEN LED
OFF: Control board fault
FLASH:Standby
9
8
4
IPM module protection
Low dc voltage protection
Compressor phase error
IPM control fault
RED LED FLSAH
0
ON:Compressor operation
ON
OF
F
Communication fault
P4
3T
YELLOW
FORCE
C
HEC
K
FORCE
PRESS
6s
TEST MODE (NOT USED)
PRESS
1s
PRESS
1s
PRESS
1s
PRESS
6s
CHECK
FORCED DEFROSTING
CHECK SYSTEM PARAMETERS
FORCED COOLING /HEATING
(CHARGE MODEL)
ONLY FOR HP MODEL
AMBIENT TEMPERATURE SENSOR( FOR HP SYSTEM)
10K RESISTANCE ( FOR COOLING ONLY SYSTEM)
L
0
-L9
IPM module protection or frequent power on/off
H4
F1
Temperature sensor fault(T3 T4 T5 TF)
Hb
High pressure(PT) protection in Heating
5
E
9E
6E
High/low voltage protection
DC fan motor fault
The discharge sensor(T5) is not seated fault
E4
CODE
3 times (P6) protection in 60 minutes,system lockup
P6
PH
High pressure (HPS) protection
P
2
P
4
P3
Low pressure Protection
(PT)
P1
P0
The discharge temp. Protection
(T5)
5P
High condensor coil temp. (T3) protection
IPM module protection
Low discharge superheat protection
Fault description
H8
Pressure transducer(PT) short or open fault
EEPROM
fault
High p
ressure switch(HPS) fault
Compressor over current protection
The module radiator temperature (TF)protection
7
E
H0
Communication fault in main control chip
P8
Hurricane protection of the fan motor
bE
2 times (E6) protection in 10 minutes,system lockup
WARNING: CABINET MUST BE PERMANMENTLY
GOUNDED AND ALL WIRING TO CONFORM TO
I.E.C,N.E.C,C.E.C,C.L.C,AND LOCAL CODES AS APPLICABLE
REPLACEMENT WIRE MUST BE THE SAME GAUGE AND
INSULATION TYPE AS ORIGINAL WIRE
WARNING
ELECTRIC HAZARD 380 VOLTS DC
TEST POINTS
H5
5 times (P2) protection in 100 minutes,system lockup
DF
Defrost mode
ON
4
SW5-1
Enter defrost
SW5-2
Quit defrost
OFF
ON
OFF
OFF
ON
Normal
Operating time is reduced by 10%
3
SW4-2
SW4-3
Not used
SW4-4
OFF
ON
Normally cooling/heating
OFF
ON
Accelerated cooling/heating
Adaptive capacity output disable
Adaptive capacity output enable
SW4-1
Not used
Defrosting extended for 60 seconds
ON
OFF
Detailed reference manual instructions
**
*
The factory Default
Normal
Figure 65
- Installation Instructions 1
- Table of Contents 3
- 1.1 Key to symbols 4
- 1.2 Safety 4
- 2.1 Unit dimensions 6
- 2.3 Location restrictions 7
- 3 Unit preparation 8
- 4 Setting the unit 8
- Line Length 9
- 6.1 Precautions 10
- Figure 14 11
- Figure 15 11
- Figure 16 12
- Figure 17 12
- Figure 18 12
- Figure 19 12
- 150 PSI 13
- 10 Service valves 14
- THERMOSTAT 15
- INDOOR UNIT 15
- OUTDOOR UNIT 15
- 12.3 High voltage ground 16
- 13 Start up 17
- Indoor Temp 18
- Insulation 19
- Figure 38 20
- Figure 39 20
- 15.3 Defrost description 21
- 15.6 Protection functions 22
- 15.7 Fault code table 23
- Table 10 24
- Figure 42 25
- Table 11 25
- Figure 43 26
- Table 12 26
- For 4860 model 27
- Drive board 27
- Error Code Description 28
- 1.Not applicable for piston 30
- Diagnosis Handling 31
- Table 21 32
- Figure 59 32
- Figure 60 32
- Figure 61 32
- Check whether the ambient 33
- Table 24 34
- Table 25 35
- Table 26 36
- IPM module protection 37
- Communication fault 37
- Figure 65 38
- Table 27 39
- Table 28 40
© 2020, manymanuals.fr. Tous droits réservés | 1.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels