Bosch PSM 18LI Spécifications télécharger pdf (Page 14)

14 | English

2 609 007 287 | (17.6.13) Bosch Power Tools

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

26.04.2013

Assembly

 Before any work on the machine (e. g. maintenance,

changing the tool, etc.) as well as during its transport

and storage, lock the On/Off switch in the off position.

There is danger of injury when the On/Off switch is unin-

tentionally actuated.

Battery Charging (see figures A–B)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The Lithium-Ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

To remove the battery 2, press the battery unlocking button 1

and pull the battery out of the power tool toward the rear. Do

not exert any force.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

in this manner.

Observe the notes for disposal.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Integrated Dust Extraction with Dust Box

(see figures C1 – C4)

Attach the dust box 3 onto the extraction outlet 10 until it

latches.

To empty the dust box 3, pull off the dust box downward.

Before opening the dust box 3, it is recommended to loosen

the dust from the filter element by gently striking it against a

firm support (as shown in the figure).

Hold the dust box 3 firmly, fold the filter element 11 upward

and empty the dust box. Clean the thin plates of the filter ele-

ment 11 with a soft brush.

External Dust Extraction (see figure D)

Slide the extraction adapter 12 onto the outlet piece 10. The

extraction adapter 12 accepts a vacuum hose with a diameter

of 19 mm.

An overview for connecting to different vacuum cleaners can

be found at the end of these operating instructions.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Replacing the Sanding Sheet (see figure E)

When attaching a new sanding sheet, remove any dust or de-

bris from the sanding plate 5 (e. g. with a brush).

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

The sanding plate 5 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 4, free the Velcro backing

of the sanding plate 5 from any debris by tapping against it in

order to enable optimum adhesion.

The machine is fitted with 2 sanding sheets that can be

changed individually, depending on the degree of wear.

 Only use the machine when both sanding sheets are

mounted.

 Only use sanding sheets with the same grain size.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-1201-002.book Page 14 Monday, June 17, 2013 11:30 AM

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 85 86

Commentaires sur ces manuels

Pas de commentaire

Bosch PSM 18LI Spécifications Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Ponceuses sans fil Bosch PSM 18LI